Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
Hi.
I'm troubled.
I use nRF52 preview DK v0.9.0 & Keil5.
i tried ble_app_hrs_c in example folder of nRF52_SDK.
This program stopped at
err_code = sd_softdevice_enable...
Hello all,
I am actually implementing an SPI-master driver in non blocking mode, I write the following code, when I use a debeug led, the program enters well in the IRQ...
I started with the blu_app_template on a 52840. I have advertising working. I can see that from an iOS app. I can also see the details of the service. I see the characteristic...
I am using the Master Emulator C# examples to build my own application. None of the examples are able to properly connect to a remote device. When I open up the Master Control...
I'm writing an nRF52 DK btle application using SDK 12. The DK comunicates with 2 external peripheral via SPI and I2C interfaces. Complilation fails with the error:
._build...
hi, i am reading mpu6050 with nrf51822. every now and then the data got corrupt because of softDevice interrupts. if i don't use Softdevice the it runs perfectly but when...
Hi All,
I am using UART with baud rate 4800, with even parity and 1 stop bit. I'm getting 6-8 bytes in a packet. I'm receiving packets for every 8-10ms continuously. This...
I am attempting to use Unity + CMock onboard the nrf51 for unit testing. I have Unity working and can even output the results of unit tests using Segger RTT libraries. There...
When I try to install nrf5X command line tools in Windows 10, I get the error mentioned in the title, even though I am not doing installing any software in parallel.
Error...
I am attempting to use TIMER4 on an nRF53832 using SDK 12.2.0 but I seem to be running into some sort of granularity issue.
Specifically, if set up the timer with 16MHz...
I just received my new NRF52480 PDK, but it will not respond to any commands.
I tried nrfjprog -e -f nrf52 and this is the log output:
-----------------------------...
Working with nRF52832 and SD132-v2.0.1
Using external 32.768kHz xtal in addition to 32MHz xtal.
I realize there are a lot of posts about timers, but I didn't find any...
I'm having difficulties writing, retrieving and deleting data from flash, using fds on nRF52832_XXAA. Sometimes the flash writing succeeds, sometimes it fails with with ret_code_t...
I want to know about some range information of the NRF52 & NRF21 (BEACON).
For example if I have TX power of the beacon +4 dBm and which is broadcasting every 500 ms so...
Hi all,
I tried to build the latest OpenThread libraries but after copying the library files in the SDK, I fail to compile the examples. Everything was fine when building...
