HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
This problem didn't appear every time when I upgrade firmware. If I restart my app again, sometime the SDK can works well.
Anyone can help? I'm use SDK in Android, Legacy...
Hi,
I am using nRF51-DK and nRF5_SDK_12.2.0_f012efa. I have programmed Proximity example from the SDK to the Development Kit and was able to successfully program the DK...
I have a function with a return value in the time slot, after the function is done inside the time slot signal callback function, I want to use the event callback function...
Hi
We'd like to set the pairing timeout when using the function sd_ble_gap_authenticate(conn_handle, p_sec_params) . The reason for this is that we are setting the connection...
(/attachment/182b723590b3c447267d5aed62b5405f)hi, i want to work on PWM to controll the vibration coin frequency for certain time period and also to change RGB values of LEDs...
Hi!
I'm reading the PS for nRF52832 and I can't find a clear answer on the following question.
If I set up a GPIO channel with pull-up/pull-down in the PIN_CNF[n] register...
Hi, I'm learning to use the nrf52832 (PCA10040).
I'm on SDK12.2.0 S132.
I've done those basic tutorials while merging codes from the examples.
My code can currently read...
Hi, i am working on TWI sensor example in SDK11 i have connected MMa7660 to PCA10040 board as per the GIPIOs. and am integrated BLE app uart to the same TWI sensor example...
Hi,
I am using a custom board with a nrf51422, SDK11, S130 v2.0.1 with central role.
I have made changes on the code to change from MID bandwidth to High. I added the...
Hello,
I'm using the Nordic BLE-UART service found in the SDK. This is the "ble_app_uart" file in the SDK examples for the Nordic nRF51822. I'm basically sending JSON back...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make only app image for DFU.
I made a command as below refering to github.com/.../pc-nrfutil.
...
Dear all
Currently we are using version 9.0.0 (nrf51422 family---> using for 51822 chip) & now we are trying to use 12.2 ("nRF5_SDK_12.2.0_f012efa.zip").
Is there...
I've discoverd a strange behaviour with nrf51822 CEAAD00 Revision 2.
I am using NRF_POWER->SYSTEMOFF = 1; for powering down the chip and a sense signal for wakeing up....
Hi,
I have downloaded the hardware files of nrf51822 beacon kit.
How to change the pcb layout of nrf51822. ( remove the name on the pcb, change the form of the pcb etc...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...