Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
No text. It's a really short question.
So this is a simple example:
NRF_ADC->CONFIG = (ADC_CONFIG_RES_8bit << ADC_CONFIG_RES_Pos) |
(ADC_CONFIG_INPSEL_SupplyOneThirdPrescaling...
Hello, I've just purchased an nRF51 DK and installed the SDK. I have Keil uVision 5 installed from a previous project, with a "Freescale Only" license key. This seems to be...
When i google for power consumption 433mhz 2,4ghz and similar most results tell me that 433MHz consumes less power... but when I look at specifications of explicit chips/modules...
I am trying to do a simple UART test with nRF51822 without BLE functionality. The code is a simplified version of the UART example in nRF51 SDK, and can be found here . It...
Hi,
I just wanted to try out the DFU on the Android app to see if I can successfully update the application on the beacon. For that, I only uploaded the precompiled nrf51822_beacon_app...
Using Blend Micro (Arduino Uno + nRF8001) to gather environmental sensor data and send to mobile via notifications. Here's my main loop:
void loop()
{
aci_loop();
...
Hello,
I know I have seen the topic on the forum, but can not find it. What changes need to be done to a example project designed for a softdevice 110 to convert it to...
The s310_nrf51422 migration document states:
Due to an issue present in this release, the application is required to set the device address to the factory default right...
Hi,
I was just wondering what the sequence of events would be in the following scenario:
A S110 peripheral device (GATT server) has a characteristic with write access...
Hi all,
I've spent 4 days now (!!) on getting a "Hello World" project to work in eclipse with GCC. I guess something around the startup-code is setup wrong in my very simple...
Hello, I'm using nRF51822-mKIT for a research.
To verify ADC readings from analog input, I've connected P0_5 to GND and ran the following code:
uint16_t adc_result;...
For my project I would like to use this bluetooth module: freqchina.en.alibaba.com/.../Fingertip_size_nRF51822_Module_Ultra_Low_Power_Bluetooth_4_0_Low_Energy_RF_Module.html...
I am trying to connect to a peripheral through s120 central and vendor has a 128 bit fixed UUID
I am trying to add it on central using sd_ble_uuid_vs_add(...,...) but it...
I am trying to develop an application for the Android that will communicate via BLE to a Nordic device. I'm able to read the characteristic's value by
BluetoothGattCharacteristic...
