Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
When nrf51822 with 32KB RAM will available? If it is going to be delayed is it possible to get samples? (I like to try IOT SDK and with my PCA10001 the heap overflows.)
...
If I don't call nrf_gzll_set_base_address_0(...) or nrf_gzll_set_base_address_1(...) what address will it use?
Also, what is the default number of send attempts?
Hi, I purchased and received the pca100028/nRF51-DK on Friday (12/19).
I've upgraded to Keil 5.12, loaded the 7.10 sdk pack, loaded the radio_test_pca100028 example ( I...
Hi
The datasheet for nRF24le1 seems to describe two ways to find out if the TX buffer is full.
Register map 07, STATUS, bit 0, TX_FULL
Register map 17...
Hi all,
I'm trying to work on my MacBook Air on BLE. I'm running Windows 7 under VirtualBox and using the new Keil µVision5.
But my problem is that whether the nRF51822...
hi all,
i have some issue about this .
when i add second vendor uuid call sd_ble_uuid_vs_add. that uuid_type.
the uuid_type always get 0x03 value.
by the BLE_UUID_TYPES...
We have some legacy code ported from other platfrom to nRF51822.
The old platform supports blocking flash write, so there will be some
readback code after flash write function...
I've had good luck running the examples such as the blinky and the basic BLE examples. Now, I'm trying to get the SPI Master example to run, but it does not seem to work out...
Hello Everyone,
As mentioned in nRF51-DK user guide, nRF51-DK has segger J-link debug out functionality. that means we can use this on board segger for downloading hex...
I have the nRF51822-DK and have been able to build and run the sample projects, e.g, ble_app_beacon.
I've just built a board using Taiyo Yuden's EYSFCNZXX module that's...
test the gpiote_example for timer0 in pca10003, the function is ok, LED blinking 200ms. but I change the timer0 to timer1 or timer2, the LED always on,and never blinking....
Hi! I use S130 on nRF51822 device.
After device is connected as peripheral I try to discover services using Master Control Panel but device disconnects. In Master Control...
I'm trying to start advertisement after establishing peripheral connection (on BLE_GAP_EVT_CONNECTED event) but called function sd_ble_gap_adv_start(...) returns NRF_ERROR_INVALID_STATE...
Hi
I'm working on a project to drive a DC motor, I really didn't find any example. I would like to know how can I program a pin in Keil, and I would be happy to have a...
