Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Does the following flasher also allow to debug the nRF51822 device?
Segger Flasher Portable
If not... which flasher/debugger is suitable to be used during development...
I'm adding the bond manager to an existing nRF51822 s110 soft device project to enable encryption when reading/writing certain characteristics of a BLE service.
As far...
i am making something about dfu!
i read some message from "readme.txt"
such as :
Program initial SoftDevice
Make sure the device is cleared (nrfjprog --eraseall...
I have trying my best to find the url of ''nrf51_sdk_v6_0_0_43681.msi'，but there is nothing i got, i need some help.
Do you know somthing about it? thanks!
Edit: One...
Hi,
We're using the SPI to communicate with a device that, when powered up, supports only up to 3Mbps SPI frequency , but after a while can work with higher frequencies....
Hi,
We have a customer requirement that he want to setup the ANCS service bypass pairing. It looks TI CC2541 could do so as below URL. Do you think it could be done from...
Hi. We're looking at nordic modules for a range of new miniaturized health sensors.
Does anyone know how to compute the current consumption of a BLE module given the data...
Hi!
I've quite wired problem with PWM based on NRF_TIMER.
When I modify CC value to adjust current value to desired value slowly (function is fired from outside event...
I have written application similar to ble_app_temp (posted by Ole Morten) and during the test I noticed that current consumption is extremly high. I used brand new coin battery...
I have writable characteristic on the server. As far as I understood there are at least two ways to access to its value: one using ble_evt_t and BLE_GATTS_EVT_WRITE another...
Hello,
i have seen here a extended version of Spi-Master driver:
devzone.nordicsemi.com/.../a00006.html
With funktions like:
-spi_master_send_recv();
spi_master_get_state...
I'm using the reference design for the WLCSP nRF51822 package, and I noticed that there are 2 pins (G3 and G4) that are listed as N.C. (No Connection) in the product specification...
Hi,
I am upgrading SDK from 5.2.0 to 6.0.0 working with SoftDevice 7 and I am facing a problem in relation with ANCS.
When I am pairing the phone (IOS 7) the first time...
