Hello
I'm currently mounting a LittleFS partition in the internal flash of my Nordic MCU. However, since data is saved regularly to this partition, I’m concerned that the...
Hi! I’m currently implementing a hook using mcuboot_status_change() inside MCUboot. I’m following the path defined by CONFIG_MCUBOOT_ACTION_HOOKS , and I’ve confirmed that...
Hi,
I'm working on a customized version of the nRF Desktop App running on an nRF5340 . In my use case, I want to connect Bluetooth HID devices (mouse and keyboard) as input...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I tried to run s130 example.
For using with pca 10005 on nrf6310 I changed settings like following.
In symbol set from PCA10001 to PCA10005.
In board_config...
I would like to ask you some questions on nRF51822 Hardware:
From nRF51822 datasheet, a 16M or 32M external clock is needed, now if we have one 26M TCXO is available...
Hi
Maybe you can help me.
I'm trying to get Device Manager to work, but I'm having several problems. Although the Device Manager is being correctly initialized and the...
Hi, I am developing a project under Eclipse Kepler & Mac OS X;
The project
When i debug, and set a breakpoint in the main.c, I got this message:
Then after Steping...
hi, i'm new in nrf module, i use nrf51822, i'm totly confuse what voltage that i should apply on DCC pin? if i want use internal dc/dc than what the voltage and if i use LDO...
after setting BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM, I getting BLE_GAP_EVT_SEC_INFO_REQUEST event,
I am using same code as the sample:
case BLE_GAP_EVT_SEC_INFO_REQUEST...
Hi
I am using v6.0.0 softdevice S110 and SDK 5.1.0
In nrf_soc.h the function sd_temp_get() is defined.
The comments there say ..
"p_temp Result of temperature measurement...
Hi,
I use ble_s110_serialization sample code.
I try to notification many 20bytes(total 5KBytes) to my phone, I add some code in ble_app_hrs.
I follow this link to...
I used nRF_Demo_Utility ios app and WFConnector.framework in a sample testing app im building. And when I tried to archive it using xcode it invalidates it with a error message...
Hello,
I’m porting the hids_keyboard demo to work with the nrf51422 dev board. I just changed the #defines for the board in project settings, as well as the pin assignments...
Is there a way to change the scan interval while scanning is on?
I can stop scanning, set a different interval value and start again but that is not my intention, it wastes...
We have some nRF51 beacons kits and we want to connect some external peripherals using the available GPIO pins.
Does any one have an idea on how to solder some pin headers...
I'm trying to implement the ability to change the beacon properties (UUID, Major, Minor) using NRF Beacon Android app. My project is based on s110_nrf51822_7.0.0 (ble_app_beacon...
I'm working with the nRF51822, using the S110 soft device.
My application includes some measurement functions that are timing critical. Ideally, the code would be atomic...
Hi,
Can I use the J-Link Edu programmer to flash the nrf51822? Right now I'm using the J-Link LITE CortexM that I get from the development kit to flash the firmware into...
