Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
I would like to drive an LED from the nrf51822 gpio
How much current can the nrf51822.
How much current can the nrf51822 gpio supply?
Is there a recommended LED for...
Hi. I am using a nRF8002 DK, and i am working with nRFgo Studio for 64 bits, in a windows 7 and windows 8 computers (for testing of the error purposes). I am having serious...
How to set READ property to a characteristic pipe through nRFGO studio.Actually i am not able to set READ property to any pipe.How can i do this?
Because i want iPhone...
Hi:
I use TIMER compare function, I open four channels and every channel produce interrupter.Here are some of my code:
NRF_TIMER1->TASKS_CLEAR = 1;
NRF_TIMER1->CC...
Hi. I've never asked a question here, and I'm a complete beginner to embedded programming, so I apologize if I break protocol in anything I do on here.
My setup:
nrfgo...
HI,all!
I have a question about downloading program into nrf51822 MCU.
That is:
As you konw, using the nRFgoStdio to download the code, you have to download the softdevice...
Hi all,
I have a devicewith display and only want a specific smartphone with my APP to connect to it.
I implement the authentication procedure at application level by...
We have some product using nRF51r22 QFAAC0.
E0 version is replacing C0 now. I just want to know when is Nordic going to stop producing the old version?
Thanks
Hi, I'm a ble developer using nrf51822.
It is a wierd question,
Is this any possible to write value to one characteristic's CCCD value from itself(device)?
This is my...
I am using the nRF51822 Development Kit
I have compiled the blink_example and the s110 ble_app_hrs in the nRF51_SDK_v5.2.0.39364.
I am unable to program the SoftDevice...
Are there any I2C examples for the nRF51822 ( write/ read functions) ?
If not, can anyone suggest a good starting point for I2C?
I am using Eclipse kepler for development...
In the nRF51 SDK examples, some pass the parameter adv_params off the stack as a locally declared vaiable in the context of the function and some pass static global variables...
I successfully made an Arduino code using nordic library that gets notification from iOS ANCS.
But some minor bug exists: sometimes i don't get any notification from the...
Hi all,
I used the ble_app_hids_mouse example in SDK 4.4.1 and found:
1.when the mouse does the first bonding with the master, the report rate could reach 125Hz(I set...
