Hi.
I am trying to disable the RESET pin (P0.21) on the nRF52810 microcontroller (custom board) and set it up as a normal I/O pin.
I'm using the SDK v2.6.0.
I don't...
Hi,
I am working on a project which has external flash (FM25V01A ) connected to nrf52832 board over SPI. And when building the project, I am getting the following error...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
Hello,
I am experiencing difficulties connecting my NRF52840 board to the nRF Connect software. Despite multiple attempts, the board does not appear to be recognized by...
I try to migrate a working code from nRF52832 to nRF5340 with the use of 7002 companion chip for the network part (BLE). However, while I can jump to main and successfully...
I am using MX25 external flash with nRF9160. I am unable to find the configuration to use the Zephyr APIs to access the flash. I am able to access it when I am using
spi_write_dt...
Hi
I tried to run the sample "hci_pwr_ctrl" from the NCS v2.7.0 on the nRF54L15.
After starting the sample, the modification of the TX power level during the advertising...
I would like to integrate the PPK into an automated test system. Are Python drivers available to query the PPK directly for current readings, power control, etc.
I'm trying to test minimum timing and performance using peripheral and central ISO under Zephyr.
I'm trying to play with the interval and latency values under the central...
When I try to debug a programm (build with "optimize for debugging" and debugging started by pressing "Debug" in VSCode) I get to the debug-view and can also go one or a few...
We are working on a custom board (gateway BIS) with the nrf5340. Currently our system is on the 2.5.2 SDK and we currently have FOTA working with an external QSPI flash and...
psa/client.h describes and defines PSA_MAX_IOVEC as follows: Just to be sure: This means that psa_call can only pass 4 input- and output vectors in a psa_call(), or? (E.g...
In the application I try to run the non-secure world mainly just calls functions/services in a custom partition in the secure world, which has more own code and also extensively...
We have started using nPM1300, but now we are unsure how to proceed.
Through our inquiries, we have learned that development requires the use of the ncs platform. However...
I have an nRF5340 that I'm trying to use a Segger Base Compact debugger with. I can flash and run the application fine. If I try to debug (using the VS Code nRF Connect extension...
Hello,
On the nRF9151 can you force usage of PC5/20dBm powerclass (as opposed to PC3/23dBm) ?
Apparently the %POWERCLASS command is read-only, PC5 cannot be manually forced...
Greetings,
One question on the nRF9161/51 capabilities: How many LTE-M DL HARQ processes are supported ?
I understand that 10 HARQ processes in DL (Rel14) is not supported...
Greetings,
LTE-M Data Inactivity Timer feature (Rel-14 ; Cf. TS36.321 §5.17 Data inactivity monitoring ; dataInactMon-r14 Info Element sent by UE) is normally supported...
Hello,
NB-IoT Dual HARQ and Max TBS size enhancement brought in Rel14 (Cat-NB2): on nRF9160 it was controllable via AT%REL14FEAT, using parameters <NB_dual_harq_support...
Hello,
One question on the Reduced Mobility feature (3GPP Relaxed Monitoring TS36.304 and Nordic-proprietary feature) based on %REDMOB command.
AT manual says :
%REDMOB...
AS-RAI (RAI over Access Stratum ; Rel-14) over LTE-M was available on the nRF9160 via the command AT%REL14FEAT (option <as_rai_support> e.g. AT%REL14FEAT=0,0,0,1,0 to enable...