I am currently working on a project where I need to connect my nRF52833 microcontroller to other devices using the Nordic UART Service (NUS). I am using the nRF SDK and Segger...
Hello! I am a newcomer to nrf and embedded programming (other than basic arduino and micropython projects). So far I have gone through many of the devacademy walkthroughs...
Hi,
We have our custom PCB with an nRF9160 SIP that is connected to a nRF9161-DK via P20. I have a couple questions about this setup.
Is it fine for us to program...
Hello,
I am evaluating the nRF9161 and nRF9151 and have a few questions.
1. In regard to modem FOTA delta firmware updates, where is the delta file stored in both Serial...
Hi,
I am hoping to send/receive binary data (a protocol) on the same UART that has logging/shell enabled. Is there a way to access the UART RX traffic that the shell gets...
I'm writing a custom bootloader for an nRF52840 using the nRF5 SDK v15.0.0. This bootloader uses the SoftDevice to receive BLE packets containing binary data for the DFU....
I am using nrf52840 and have two questions regarding flash memory.
1. If the write erase cycles limit is reached for certain page of the flash, only that page is going...
Hello,
I recently purchased a few NRF9161-DK boards for both LTE and NR+ evaluation. However, I am unable to run through the initial demo. The board is discoverable initially...
Hello. I'm using serial lte modem as mqtt client.
After a while I receive fault. Adding logs:
#XMQTTEVT: 9,0 ESP:LTE: PINGRESP packet #XMQTTEVT: 9,0 PINGRESP packet CR...
Hi, I read somewhere that the LOG module works differently from printk() and uses a separate thread or so. But I couldn't find any information which priority this thread uses...
Hi there,
I am currently having issues flashing an nrf52840 DK on windows 11 using either west for a Zephyr project or nrfjprog. I have successfully done this on a work...
Hello,
I am designing a custom PCB using an nRF5340 and am unsure what my options are for how to program it.
I've seen a number of forum posts saying that you can program...
I've been working for a year now programming nRF5340 DKs using nrfjprog and I still can't seem to figure out what is the right way to program them. It is also very random...
Hi, I am working on the nRF5340, We will be using the nRF5340 for the device that we are designing.
How to do the very first production DFU/First firmware upload,.
I...
I have a device nRF5340 with multiple advertisers who have different services.
I differentiated the address with bt_id_create(), but I would also like to differentiate the...
Hi,
I'm creating a new ticket for a questions asked a few years ago:
I'm in the process of also developing an app to send some data I've collected from nRF Cloud to Android...
Hello,
I have a custom board running as a low power node, consuming around 17uA during sleep. When I have messages back and forth, the node goes back to sleep as usual....
Hello. I'm completely new to nRF cloud. now my iot device is successfully sending the data to the nRFcloud.
now i'm building an android app and i don't know how to get that...
When i call the custom-code certify() function inside my code in a secure partition i can build the programm, but after clicking flash/running the secure uart-output prints...
Is there a DTM sample for the nrf52dk_nrf52832?
I see the sample supports nRF52840 and higher according to the docs.
I tried selecting the nRF52dk, and everything compiles...
Hello,
As the LE Audio controller for nRF5340 library is deprecated in favor of the Nordic Semiconductor’s standard Softdevice Controller. We have started to use the Softdevice...