We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi Dears:
When I downloaded and installed nRF Connect v3.3.1, the following screen appeared.
I remember when there was a drop-down box to select the BLE component. ...
Hi,
I would like to investigate some BLE issues on DFU project, but I couldn't find the implementation for advertising, connection and disconnection.
Where can I find...
Hello Nordic team!
I'm working on a BLE app with the nRF52-DK and an armband(M6) that has a heart rate sensor. My goal is to discover this service and read those values...
Dear ,
With nRF connect SDK, is there a way to check if the SD card is formatted with the correct file system, i.e. FATFS? If it's not in FATFS, how can we format it via...
We've upgraded our nRF9160 modem firmware and would like to downgrade to the pti_v1.1.x image so that we can test production test commands such as %XMIPIRFFEDBG. Where can...
Is there any info, which helps to distinguish between the versions of thingy 91 when ordering?
According https://www.nordicsemi.com/Products/Development-hardware/Nordic...
Hi Nordic Team,
I have a custom application running based on nRF NCS 1.5.0 with MCUboot enabled.
I'm having an issue where MCUboot simply doesn't jump to the application...
I had to reinstall Keil after running into some issues and lost most my packs. My project uses the NordicSemiconductor.nRF_DeviceFamilyPack.8.15.0 and the NordicSemiconductor...
I want to expose 2 endpoints on the nrf52840 DK - one is the existing Onboard LED and the other is the GPIO pin (P0.02) which I have enabled in overlay.
I am extending the...
Hello,
We are using A-GPS in our application to get faster TTFF and will be reading location coordinates after every 5 mins of duration. The application flow looks like...
Hello, On a custom board, using the NRF52832, we want to know the value of a potentiometer. This value is send via a signal on the AIN5 pin of the NRF52.
So, I tried to...
I am using nrf52833 to make a Thread end device as SED and RCP. All firmware versions use NCS V1.8.0.
The compilation options for OTBR is: CMAKE_OPTIONS += \ -DOT_THREAD_VERSION...
Hi,
I use the BLE_APP_UART example for reference and in the code there is the ble_evt_handler with the following states:
case BLE_GAP_EVT_CONNECTED: case BLE_GAP_EVT_DISCONNECTED...
Hi,
I faced the exact problem nda , here . I take step just like nda did before. I unchecked "Enable debug options" as Marte Myrvold told, but still the same problem.
...
