i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hey guys ,
I am trying to merge ble_app_uart code with RTC peripheral code . RTC code works fine when I try it on SDK but after merging with ble_app_uart code it doesn...
Hi,
I have a question about the connection handling when we have two connections to a single smartphone.
The smartphone runs two Applications:
App 1: Acts as central...
Hi,I recently started using a PPK2 board and at first had no trouble setting it up with the Power Profiler Software from the nRF Connect for Windows.
What I realised is...
Hi,
nRF9160 in nRF9160DK with NCS v1.6.0 and master, power consumption measured by PPK2.
With CONFIG_SLM_EXTERNAL_XTAL=n nRF9160 average power consumption is ~7uA after...
My use case is that the nrf9160 is running as a serial lte modem and I have a host controller that is controlling the ENABLE pin. VDD will always be powered so can I leave...
Hi All,
I am using a 3rd Party (Japan) nRF51822 module in a device and it is running a modified Direct test mode firmware without Soft device. Upon testing, it is found...
Hi everyone!
I'm trying to make the NFC work on a custom board. I'm using a BL653 series (nordic nRF52833) and nRF Connect SDK v1.6.0. I am running the record_text example...
I found a similar thread for this issue, but there was no solution... So I want to ask here again here
I follow the video "Introduction to the Zephyr RTOS"
https://www...
We are using a IDE Segger Embedded Studio (SES) for our development with nRF52832.
We need to use IDE which supports IEC 62304 standard.
Our Query as follows:
1. Is...
Sometimes when I call sd_ble_gatts_hvx, it can take several ms to return. Most of the time it takes very little time (<1ms), but occassionally it takes up to 34ms, my connection...
Hi Nordic Team,
In my application, I'm trying to read 512 bytes of data continuously from the STM32 master device. nrf52840 acts as a slave device. Every time I receive...
I have a DK of nRF52840, which is from 2016, and want to use it to test the LE Coded broadcast.
But it seems that 2016 DK does not support it, so I want to replace the chip...
Hi
I am working on direction finding examples, based on CTE feature that is introduced in BLE v5..
I have build and run both "tx" and "rx" examples successfully as described...
