i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
We are trying to upload Bootloader only, but it fails with 'Error 5: FW version check failed'. Please view log / pictures.
We have tried to change the bootloader version...
Hello,
there is the following page:
https://github.com/NordicSemiconductor/IOS-Pods-DFU-Library/blob/master/documentation.md
Known issues
Since iOS 13.3 (?)...
Hi all. I've seen a few posts about this, but none of them seem to have the knowledge I'm looking for. I am helping plan a device that has two units and will connect to a...
Hi, guys.
I'm using nRF52 DK (PCA10040) and 16x2 LCD ( ST7032i ). I would like to create a custom icon (e.g. degree Celsus ℃). Here is my code. It doesn't print anything...
Hi,
I would like a solution for encrypted OTA firmware update and I just realized that the Secure DFU doesn't enrypt the firmware image just sign it.
I find this Q&A:...
Is there a way to change the Thread SDK example program (\examples\thread\ncp\ftd\uart) baud from 115200 to a higher 460800? If so, what steps are needed to make this change...
With SDK For Mesh v5.0.0 the replay cache is saved to flash using MESH_CONFIG_STRATEGY_ON_POWER_DOWN. In mesh_config_load() a check is made to ensure that there is enough...
Hi,
I'm working on porting BG95 to nrf52 sdk, it'd be a lot helpful if I can get a head start with some open source implementation(AT parser libraries, drivers porting etc...
Hi,
In the Product Specification for nrf52840 it´s written that setting CONFIG (0x50C) register to Pause (0) would pause the watchdog while the cpu is halted by a debugger...
nrf52840 with SDK15
I am trying to update 3 characteristics if the correct value is written to an authenticated read write characteristic. Actually all of my characteristics...
I'm trying to create a simple point to point link using the nRF24L01+ with a new non-arduino microcomputer. I've searched the internet for example Python programs but only...
Hi,
I would like to double check with you if 9-pin cortex-M adapter board for Jlink can be used and connected to PPK P21 connector : https://www.segger.com/products/debug...
Hi Team,
We are using the nRF52840 DK for one of our project, as part of that we are using internal flash one of the sector with start address of 0xfc000.
We have written...
Hello, we are having a low occurrence issue when attempting to write some data in NVM using fstorage.
We are using a nRF52832 as a BLE peripheral using SDK15.2.0 and SoftDevice...
Nordic colleagues,
We just received our nRF 52840 DK and are attempting to install the nRF Sniffer application to use with Wireshark. We were able to program the DK with...
