I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hi,
I make some tests on power consumption of nRF52 with evaluation board and I remark some peak on the current. it's appeared that this peak is generate by DEC4 output ...
Hi, if i pair my nrf51-dk with my iPhone works, than I pres discontent (bluetooth settings),
now,
if I try whit another iPhone this doesn't work...
If I reset the board...
Hi,
I think there's an error in SDK12's nrf_drv_uart, some code parts unconditionally use p_instance->reg.p_uart (eg. nrf_drv_uart_task_address_get, interrupts_enable)...
Hi
Recently in the release notes of the SDK12 I noticed a line about updated the MDK update:
Included a critical MDK update (v8.7.1)
My SES project uses the...
Hi,
Is there an example available for Nrf51822 BLE HID (nrf5 SDK v11) with Feature and Output reports?
I've added an output HID report to HID mouse example from SDK and...
Hello.
I use nRF52 and tried to make the shared channel.
There are 1 Master and 1 ~ 3 Slave device.
When the master device send the notification messages to slave...
Hi,
I just did a quick diff using these two commands
> find nRF5_SDK_12.0.0_12f24da/ -type f | grep --text -v -e "c$" -e "h$" -e "s$" | sed 's/.*\///' | sort -u > exclude_list...
Hi
we are switching from NRF51 to NRF52.
Putting the same (very basic) inits for sd and advertising, leads to NRF_ERROR_INVALID_PARAM..
This is my source:
#define...
Hi,
I downloaded the latest SDK V12, coped the example HEX from the BLE Beacon and it worked fine.
I tried to then compile using Keil, it compiled, but I noticed that in...
Hello,
I am currently using the TWIS (slave!) peripheral to get data from a I2C master. Now I would like the ability to place the nRF52 in deep sleep mode with sd_power_system_off...
i am using UART service for implementing BLE App on iPhone-4s by using objective-c.
i downloaded old source code of UART but it can't work.
so can i get latest updated UART...
Hello Everyone,
I am working on nRF51 can any one tell me how can i get current time in microsecond?
micros() return current microsecond time in arduino. I wants same...
I am new at this, I need to enable the OTA DFU mode on a nRF51822 QFAC chip on a pcb (the pcb has bluetooth).
how can I program it? what do I need to configure?
I am trying...
Hello,
I can't copy file from mail after updated nRF Toolbox to v4.0.4. (iPhone5s & iPhone 6Plus)
The app crashed when I select Copy to nRF Toolbox.
Any solutions?...
