I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi，I use nRFgo Studio to erase nRF51822, like this
but it display: ERROR: Invalid serial number!
I found the question how to use nrfjprog --snr??? ，I can get the...
I am using the nrf24l01 on a FRDM k64f board, I want to communicate between the board and my laptop, so I have bought a nrf51 dongle.
I am using mbed on the k64f board...
I try to create a custom boot loader that enable to update soft device via data come in from SPI msg. When I try to use the command nrf_nvmc_page_erase() to erase the flash...
Hi everyone,
I'm a beginner in Android development and BLE environment, and I want to communicate with the nRF52 card using an Android app. In fact I have to develop an...
hi,
I am using the nRF51 with code from SDK 9, as well as the S110 softdevice and made a custom service(128-UUID) with bond using device manager.
connection and service...
Hi,everyone,
I would like to know that what's the dedicated bonding ?
I saw this in the introduction of a BT chip.
I am confused with 'dedicated bonding'.
And what's...
Hi,
I am using the nRF52 with code from SDK 9.2, as well as the S132 softdevice. I basically ported code from the ble_uart_app into the twi_example to send data over bluetooth...
In the very first blinky example from the nRF52_SDK_0.9.1:
#include "stdint.h"
#include "stdint.h"
#include "nrf_delay.h"
#include "nrf_gpio.h"
#include "boards...
hello,my experiment phenomenon is:one nRF24L01's channel is 0x0A,used as send terminal；the other one nRF24L01's channel is 0x02，used as receive terminal；receive terminal can...
I try to make a build of the example ble_app_hrs_rscs_replay_pca10028 (central and peripheral experimental) in SDK 10. My MCU is nRF51822-CFAC, and I'm using IAR compiler...
I'm using custom board with 32MHz oscillator and S110 SD 7.1 (SDK 6.1).
Somteimes (quite rare) the chip completely hangs when calling sd_flash_erase in pstorage.c.
Only...
hello
we use nRF51822 QF AC A1 / IC rev 3 with SDK 6.1.0 / S110 7.1.0. We have produced and delivered to client > 1k units
pwm code nrf_pwm_noglitch 02.2015 from
github...
Hi!
If you look at the reference design for nrf51x22_ceaa the pad size is 0.18mm with a 0.076 mm solder mask expansion
BUT in application note nAN-38 (page 6) it is...
Hi!
I have NRF51822 QFAA pcb. I uploaded mbed bootloader with DFU through uVision & st-link V2 interface. I have Windows Phone 10 (Build: 1511) installed on Nokia 830. Nokia...
