S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hi,
At present time I perform many tests with power level and link stability. And noticed that if cover nRF base device with hand or put into pocket the disconnection with...
Hello,
Is there any way to configure the flash data default values during programming phase with Keil IDE?
In IAR, it is possible using a file ".s43" included in the...
Hello, I'm using the nRF51822_QFAA chip on a custom board, but the layout and parts are the same as on the nRF51822 USB dongle . I tried flashing the Board\pca10001\s110\ble_app_hrs...
I am using nRF8001 with EMF32.
inside hal_aci_tl_send function
C : 1, 14,
inside hal_aci_tl_event_get function
E : 3, 132, 128, 130,
It is looks like
Length == 3
...
Hi,
I am working on a small (1 inch square) bio-sensor project that needs Bluetooth capabilities. I like the nRF51822 and was looking into the dev board ( www.nordicsemi...
Hi
I am setting up a production programming script, and would like to know if it is possible to write short strings or numbers directly to flash. For example, i would like...
I use an ISP 130301 Development Kid for getting familiar with the nRF51822.
I flashed SD110 on the Demo Board with nRFgo Studio and compiled and loaded the proximity example...
Hi, I have a project where I need to communicate using UART BLE between nRF51822 and a PC ThinkPad with Windows 8 and embedded BLE4.0 hardware.
I have programmed the nRF51822...
I'm running into a hardfault. I perform some initialization and enter a main loop. At the end of the main loop, I put the soft device into sleep mode and wait for an interrupt...
Hi,
Recently I updated my SoftDevice on beacon from 7.1.0 to 8.0.0. Unfortunately, I met the same problem with advertising timeout which I faced with in SD 7.1.0, but the...
Hi all,
I have some doubts over the memory management of nRF51822 and nRF51422-EK.
I have gone through the link in this forum where it is explained buy I'm still not sure...
I'm trying to build a project of "nRFUART_GoogleAPI_Android4.3+" from the following link.
[https://www.nordicsemi.com/eng/Products/nRFready-Demo-Apps/nRF-UART-App2]( www...
I have one doubt after reading the definition of PSTORAGE_MAX_APPLICATIONS and PSTORAGE_DATA_START_ADDR in pstorage_platform.h and the actual computation of used flash memory...
MCU : NordicSemi nRF51822-QFAA (Using custom board)
SDK Version : 7.2
Softdevice : S110 7.1
Using IAR for ARM 7.1
Hi, I was migrating my codes (SDK 6.1 to 7.2...
I am using the ble_app_template, together with one timer called every second. The timeout handler of the timer just prints a short string on the serial port using simple_uart...
