Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
What this ticket reports
We ship a battery-powered nRF5340 product using the nRF Connect SDK's documented production security configuration: immutable bootloader (NSIB/b0...
Hello,
I have been a Nordic DevZone member for several years, but I have never published a blog post.
I would now like to contribute a technical article about an open...
Hi,
I've been developing the next version of our product with an nRF54L15 There's external SPI flash attached on QSPI via SQSPI which is working ok (albeit it is very slow...
Hello,
I am trying to understand how the documented tRXCHAIN value relates to the timing of EVENTS_ADDRESS in BLE 1M mode.
In this DevZone ticket:
https://devzone.nordicsemi...
Hi DevZone! I'm migrating an app running on a Thingy91 from SDK 2.5.0 to 3.4.0. I will eventually try to adapt it to the newest Thingy91X. So far I managed to migrate the...
Hi all,
We're building a PoC of a simple BLE device with a following setup:
custom PCB with nrf54l15 rev2 and 32MHz oscillator
FreeRTOS + custom port
nrfx version...
We are observing an unexpected increase in current consumption when enabling the LED driver outputs of the nPM1304.
We configure the LED drivers to Host mode , which by...
Hello Nordic support,
We are preparing a build-only NCS2.9.0 environment on an Apple Silicon Mac, macOS26.5.1 (25F80), with commands run in a managed workspace execution...
Hi, i have downloaded the app nRF for desktop, but when i try to download an app inside it (such as Programmer or Direct Connect) i get notified with this error
i try...
Hi Nordic team,
I am following up on a previous thread ( nRF54L15 sQSPI support for SPI NAND in NCS v3.3.1 ) where it was confirmed that NAND flash was not supported in...
The nRF91 series of modem firmware are distributed with FOTA-TEST diffs to allow for validation of FOTA integrations. Will the nRF93M1 firmware images be distributed with...
NCS SDK 3.4.0 NRF54LM20DK
The nRF54LM20A data sheet warns against using the same RAM subordinate by more than one bus manager. From section 4.2.1,
Avoid situations where...
