This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
Hi Dev Zone !
I am actually using nrf52840-dongle for wireless communication with the protocol Enhanced ShockBurst (ESB). I would like to connect an external antenna to...
I am getting ready to release a nrf52 based ble product. These products are connected to a BLE to wifi bridge. So I can talk to them at any time.
I have been using the secure...
I've been evaluating the nordic SDK. I was able to install 1.6.1, 1.7.0 numerous times. I've been working with one of the individuals there at Nordic, and I wanted to do a...
The peripheral application I'm working on implements a service which must handle multi-byte incoming messages from a central device and would welcome a pointer to any example...
Hello
I found a possible bug in NCS 1.7.0 which was introduced in PR #5353 .
1) False UNKNOWN event when disconnecting
The "invalid cell id" check leads to an false...
Hey
I'm using the softdevice s140 in my project (and the latest SDK 17.x).
I successfully enable the softdevice and am able to start an advertising (as peripheral). However...
Hi
The baseline current consumption running the azure_iot_hub is very high.
I'm using nRF Connect SDKv1.6.1. The sample connects and sends data to azure as expected. But...
Figure 4: Memory layout
Shows code RAM beginning at 0x0080 0000 but nRF52832 Engineering A Errata 33
"Code RAM is located at address 0x0800_0000".
Additionally 0x2100...
Hi,
I am developing a product based on nrf52840 soc as a central Bluetooth device. I want to connect to a Bluetooth device (as a slave) while it is advertising, but unfortunately...
Hello everyone, i'm trying to run the button sample with Pull_up on the pin P0.27 i did the wiring like below
power->VDD nrf-HV
GPIO->P0.27
i attached a resistance between...
Hi,
Does nRF5340 require any calibration in production line in terms of below items. If so could you share any documents on them
- Gain for the RF front end
- Crystal...
Hi, helpies
I am currently workibg on nrf52832 board and now there are some changes in the hardware and we are left with pin shortage,so we planned to upgrade to nrf52840...
Hi, I am implementing NUS which is based on example BLE_NUS & BLE_NUS_C. The connection is not 1-to-1 but 1-to-7. i.e. 1 Central connects to 7 Peripherals. Although ultimate...
I tried following the " Bluetooth low energy Services, a beginner's tutorial ", I ended up getting stuff to compile and run by making a copy of the ble_app_hrs example, and...
