Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hello,
I want to use a Li-Po battery with my nRF52833 development kit and I can't find the specific name of the J6 connector in the DK documentation. Does anyone know...
Hello ! I am working on the asset tracker project on NCS 1.4.0. Since I switched to this NCS, I have an error that comes up very often (once in two or once in three): get...
Online rajAsthana a few seconds ago in reply to Einar Thorsrud
Hi Einar,
Now I am able to put my board(nrf52840) in DFU mode with buttonless code using Esp32 as...
Hi,
I using nrf52832 evk board and sdk17(S132). I want to add the internal temperature sensor reading to the ble_app_buttonless_dfu_pca100400_s132 code present in the examples...
Hi,
1st time using nRF52840 - EV-BT840 on Keil V5.25.20
I use SDK 1702, reference to example examples\dfu\secure_bootloader\pca10056_s140_ble
My question is what softdevice...
Hey,
I have isnstalled ncs v1.3.1 and the toolchain specified in the instructions ofr 1.3.1.
I am trying to utlise the date-time library in the https_client example. ...
Hi Great Nordic Support Team:
Our clients are developing products with 『 nrf52840-WLCSP』. And they find out that there are some mis-information on the spec.
It's described...
Hi,
Dear nordic friend,I am trying to download NCS1.31 by using toolchain manager,but it work bad,show in below.
I have use some ways，to make me can visit the web in Europe...
Hi, I'm having difficulties driving SDOUT when it's configured to pin 19 on the NRF52840. I can operate the peripheral and see output data when my WS2812_PIN macro is assigned...
Hi all,
I am interfacing with a CAN Controller (MCP25625) that sets an Interrupt pin when data is ready (active low). That pin is then connected to a GPIO on the nRF9160...
Hello
I'm using a passive buzzer controlled by PWM. When PWM is set and run, the buzzer will continue to output small noises.
This is probably a code problem. Below is...
Hello everyone,
I'm programming nRF52833 for my own application. In my application, I have a button to turn on and turn off the supplier. There is only 1 button so that...
Hello,
I contact to you because a customer bought the bluetooth development tool part number NRF6939, and they asked the following below;
"
Can you specify whether there...
I have been testing a sample project that has compiled and worked fine for a week. But now it is giving build errors related to Zephry.
I think a broke a configuration,...
