We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Been beating my head against this for a couple of days and came across a number of people on the forum with the same issue without a solution, so hopefully this saves someone...
Hi all,
I have some issue setting up the advertising data on my nRF52840 Dongle. I'm using the ble_template to develop my software and in my application i need to fill all...
Hi all,
can i send a scan request from an nRF52840 dongle using the nRF Connect - Bluetooth Low Energy software? I need this during development of my application where i...
Hi
I am seing framing errors when receiving using UARTE.
It is not external hardware, I have checked with different other interfaces and measured timing, no problems there...
Hi
I want to ask a few question.
When the phone sends a specific signal after connecting to the MCU, the MCU is sending data in real time.
When the power is turned...
Hi,
I was trying to find out if it is available to have authentification before connection and I found this link and it makes sense to me but that Q&A has been over 4 years...
Hello!
I use Zigbee CLI example and multi_sensor example on nRF52840. (examples/zigbee/experimental/cli/cli_agent_router and examples/zigbee/experimental/multi_sensor) ...
I have nrf52840 dongle and sdk nRF5_SDK_17.0.0_9d13099.
I would like to know, is there is an example in which, Advertisement Data is stored in flash memory and reading and...
I USE 9160 with i2c ，send data. then it tips :
[00:02:07.716,918] [1;31m<err> i2c_nrfx_twim: Error 195952641 occurred for message 0[0m
what is wrong ?help me ,thank...
NOTE: This is related to the following issue: https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
--------------------------------...
Hi,
I would like to read data from sensor and send it over BLE to nRF connect. Unfortunaly, something went wrong while reading the data by TWIM.
I´m using SDK16. ...
Hi Sir or Madam,
I tested examples\zigbee\light_control demo recently and I want to test install code function based on this example, the first step is I add install code...
Hello,
I’m interested to replace a part of my project by a dongle. The current prototype of the project comprises two Nordic nrf52840-DK boards, an Analog Devices Eval,...
Hi,
during the test of the trasmission, in my phone I have seen the figure below:
As you can see the trasmission is every 2 seconds and I want to change this time trasmission...
