when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Hi there,
I am using WIN10, Segger studio 4.52c and nRF SDK16.
I can successfully run ble_app_uart example on PCA10056, but when i try to run same code on fanstel EV-840...
Hi, I have been working on setting up the environment for development of nrf52840 and nrf9160 the past three days. I have nRF9160 dk which comes with nrf52840. I have been...
When I built and run your example Bluetooth: Peripheral HIDS keyboard and I saw the following errors in logs: E: set-value failure. key: bt/ccc/283926aaa86c0 error(-2) E:...
Hi,
We would like to know whether below gang programmer can be used for gang firmware flashing of NRF9160 application FW and NRF9160 modem FW.
Also we would like to know...
I am getting the following error when trying to register a nRF9160-DK with a HWID. There was an error adding your device: nRFCode 40001:
Please advise how to move forward...
Hello!
I've got a couple of NRF52832 based modules - Holyiot-17095-nRF52832. These modules are presented in the list of supported - https://www.nordicsemi.com/Software-and...
I performed below mentioned steps:
Downloaded SDK 12.1.0
Soft Device s130_nrf51_2.0.1_softdevice.hex
Built secure boot-loader with new public key
Built project ble_app_hrs...
I'm trying to compile hci_usb sample of Zephyr with Nordic Connect SDK v1.3.0 using Nordic's proprietary controller but apparently it fails.
I'm using following configuration...
Hi I'm doing the Bluetooth GATT: How to Design Custom Services & Characteristics [MIDI device use case] example ( https://www.novelbits.io/bluetooth-gatt-services-characteristics...
I cannot get the NRF_LOG messages via RTT to the debug terminal in SES or RTT Viewer. My setup: HW: PCA10040 1.2.4 SDK: 15.3 Project: \nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral...
Hi
I'm using SKD16.0.0 and S132, and I want to realize that peripherals can only connect to a center with a known MAC address through directed advertising. How should I...
Hi Folks,
I am getting in trouble with SoftDevice activation. Indeed, my application did not return from the "nrf_sdh_enable_request()" call, more precisely it hangs into...
Hello,
I am currently working on BT840 and BT832 modules and trying to run the sample codes which are given by Nordic (specifically ble_app_uart which runs with UART service...
Hi,
there is a number of tickets on the sd_ble_gatts_characteristic_add, but I still can't get where I do it wrong :-(
I'm trying to initialize the battery service using...
Hi,
I used 52840DK and SDK15.2 to test usb cdc, every thing goes will, but in rx event, it always missed first byte, for example, if send "123456", it just received "23456...
