I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi,
I have a smartwatch that has a nrf52832 chip inside. It firmware runs on S132 SoftDevice ver 2.0.1 and has an OTA bootloader which supposingly allows me to upload firmware...
I am evaluating the nRF5284 SDK 15 Module in HCI mode. I am trying to scan Extended advertise when: 1.Extended non connectable non scannable advertising, Primary_Advertising_PHY...
Hi,
I have just purchased a nRF52840 usb dongle ( https://www.mouser.in/ProductDetail/Nordic-Semiconductor/nRF52840-Dongle?qs=gTYE2QTfZfTbdrOaMHWEZg==) .
I would like...
Hello, I am a beginner and I just got a Raytac "MDBT50Q" bluetooth 5 module based of nRF52840 Soc.MDBT50Q does not come with a builtin frimware to respond to AT-commands.Can...
Hello, i have this problem with DFU, in Mesh SDK v3.0, i am using PCA10040.
this is my boodloader_config_default.json
and i am using this for make the pkg.
and...
Hi!
For our development purposes I am implementing NRFUTIL 0.3 for mesh on Android/Java, migrating it from Python code, via UART/Serial, for DFU purposes
It looks like...
Hello,
I am having difficulty using a single TWI to support a DAC (MCP4725) and IMU (BNO055).
I am using nRF52 DK, and SDK 14.3 with the SEGGER IDE. The DAC is running...
Hi,
I am trying to run lte_ble_gateway sample on nrf9160 DK, but in debug I can not catch breakpoint on main().
When I going in debug mode step by step I find that the...
Hi
I am new to the NRF52840. I am trying to receive data from nrf24L01+ to the nrf52840 Development kit. I find some examples from the SDK radio receiver using PCAl0056...
Hello all：
I am using nRF52-DK（pca10040）to do some tests.
I want to use gazell and at the same time, I want to detect the events of the NRF_RADIO, connect it to PPI. ...
Hello,
I am using Eclipse to create a project using code from ble_app_hrs and I am developing for a nrf52832 chip. Unfortunately, I am getting a "was not declared in this...
I send a sequence of characteristic writes to my device, in code based on the nRF Toolbox. Sometimes I see this error message. Why does it happen and what steps can I take...
Hi Team
I created an own interface layer using the mesh SDK's "flash_manager" to have a simple API for accessing my application flash area.
Now, I am facing the problem...
Hi there,
I am migrating a project from SDK13 to SDK15.2, where I need to change the advertising data dynamically and change the ble_gap_adv_params_t properties type between...
I am using SDK12 with nrf52832. UART working fine (with FIFO) and Timer1 also works.
I wanted to set a 1 minute timeout around the UART dialog to handle disconnection etc...
