Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hello,
I am using the nRF52832 WLCSP with the imprint "N52832 CIAAE0 2207A5", and my FICR reports a codepage size ox 0x400 and a code size of 0x100. This results in a...
Can the nrf7002 be set up to have both a STA virtual interface and an AP virtual interface at the same time?
From all the documentation it doesn't specify that only one...
I am using the Nordic Mesh Library with an ESP32 IDF-based application on the ESP32 side, and I am using ESP32 BLE Mesh. On the Android side, I have created a node to send...
Hi,
We are using the nRF52832 in a battery such that we have a 3V3 LDO configured to turn off under a certain battery voltage. Now during testing we have discovered that...
Hi,
I have made my own custom board with the nrf52811. Therefore I was using the nrf52dk.
I have made connection with my custom board and simply want to blink an led....
Hi,
I am using nRF54L15 DK and nRF21540 EK together. I am using the GPIO FEM mode. Below is my projconfig:
I notice that I cannot use 21540 EK in 54L15, the overlay...
Hi,
I am trying to pull up P0.08 as an enable pin for this switch TPS7A0518
I use the following code and verified on development board
However, when I move to...
Hi, we have a product in production and we are using the HWID which is accessible via this API https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/libraries/others/hw_id...
Hi Nordic teams,
There is have issue when I compile the V2.9.0. For more details
C:\ncs\v2.9.0\nrf\applications\nrf5340_audio>west build -b nrf5340_audio_dk_nrf5340_cpuapp...
Hi,
I m using SDK 2.9.0. After building and flashing my target board based on nRF5340, I get the above kernal panic error.
This is my .config.
and my prj.conf
Are...
Hello,
I was able many times to download nrf52-ble-image-transfer-demo-master in to nRF52840 DK (PCA100156) and run a mobile application successfully.
Today I downloaded...
Hi ! I'm using nrf52 + SDK 17.1.0.
I found sd_mutex_acquire/ sd_mutex_release, which is great for locking variables that are set/get asynchronously. Next, I'd like to use...
Hi, I'm using nrf52840DK.
I set the selective_auto_ack as true. It should be able to adopt dynamic ack (or ack payload).
I have two data packets, which are ch_pkt and...
