This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
Hello,
the BSI (German Federal Office for Information Security) released a document February this year which contains a list for recommended cipher suites and TLS versions...
hi ,I am using nrf52840dk- nrf52840 board to interface the IMU Sensor using I2C using nrf connect sdk for vs code. But I am facing error:
i'm using the code in ncs/samples...
Hello im using basic usb over console exaple on my custom board . i believe this task wont require any pins to be configured as my custom board is routed properly to all 4...
Hello,
with the help of this documentation ( https://docs.nrfcloud.com/Devices/MessagesAndAlerts/SetupMessageBridge.html ) i have been able to create a bridge to transfert...
I am trying to test a nRF5340 with a 1.3 inch waveshare 240x240 display using a st7789 driver. How would I connect the display to the board:
VCC
3.3v
...
sdk-nrf: v2.7.0
When PAWR is enabled I no longer get connection timeouts as a callback to bt_conn_cb.connected with the conn_err parameter set when attempting to open...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
Hi,
I am using nrf52832 board and I want to configure the SPI0 and SPI1 for the sensors LIS2DW and BMP388 respectively.
I am new to nRF Connect SDK for VS code, I am exploring...
I have installed version 5.0.2 for NRF connect Desktop and on that I have been trying different versions of tool chain manager ranging 1.3.0 to 1.5.1 none of them is loading...
To measure the current consumption during system off on the NRF52833DK, I followed these steps:
Cut the SB40 bridge.
Connected a multimeter to P22.
Here's what I...
Hello,
I would like to analyze the nfc_launchapp example from the SDK to understand how NFC tags are recognized.
Specifically, I want to examine the relevant code portions...
I'm using the peripheral AES CCM to encrypt frames on the nrf52832 board but I'm not using the on-the-fly encryption (at the same time as the radio).
I managed to correctly...
I was following this lesson on paring and passkey authentication:
Exercise 1 - Nordic Developer Academy (nordicsemi.com)
Is there a way to get the popup for the pin...
Hello DevZone,
I am using a nRF52840 with sdk 17.0.2 with Windows 10
I am trying to setup a connection to my Windows PC but I noticed data fragmentation and a queue...
I would like to analyze the nfc_launchapp example from the SDK to understand how NFC tags are recognized. Specifically, I want to examine the relevant code portions.
However...
