Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi,
For the nRF52840, can we use another pin than P18 to realise the Pin RESET functionnality?
I can write the register NRF_UICR -> PSELRESET with numbers other than the...
Hi Devzone,
I am facing an issue in my application where my device is working as a BLE peripheral advertising for connection. The device stops advertising after connecting...
I'm trying to download and flash an MCUboot image at runtime. All goes well, the image is flashed to the secondary slot, confirmed, and marked for upgrade. The secondary slot...
I use the nrf_dm demo program, when using the nRF52840DK development board, the program can print the log normally.
Then I changed the build configuration to nRF52840Dongle...
Hello,
I have a custom nrf5340 board with a simple firmware flashed on it (turn on red led). My board has a hall sensor as a turn on/off switch (latched). If I connect it...
I used nRF52840 board with SDK 17_1_0 ,
Using FDS I am able to read and write data into flash when nRF52840 board Continuous ON,
But when i Make nRF52840 board Power OFF...
How can I blacklist BT LE channels/frequency from operation? Context: I have the nRF52840 integrated into our product's design. The device is going into an environment where...
I just upgraded my nRF Connect for VSC to 2.6.1 and now am getting these errors:
and
I saw this as well:
but I have CONFIG_DISPLAY =y in the prj.conf....
I have an application running on a custom nRF5340 board that supports simultaneous BLE DFU of the network and application core with MCUBoot. This ticket: seems to indicate...
How can I properly set up the SWD interface for printk on a custom PCB? I have to build my project example and see the message printed on the VS Code console. My custom hardware...
Using nrf5340 as both Central and Peripheral roles and I have implemented the Basic Audio Profile based on the nrf5340 audio example. I am using nRF Connect v2.6.1.
I...
I need a bluetooth module that is capable of simultaneously streaming audio two way, ie two channels stereo out and 1 channel mic in with low latency. A friend had recommended...
Hi folks!
As always, I'll start with relevant environment details
===== Environment =====
nRF Connect SDK v2.5.0 (though not opposed to upgrading to one of the 2.6.X...
Hi,
We are developing a device using nRF5340+nRF7002 running Matter. The problem we have is the code size which is around 900KB when Matter is enabled. This leaves us with...
