I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I'm working with NRF54L10 module. I needed more mcuboot space so in pm_static.yml I allocated it 80kb. Before this FPROTECT was working but after I allocated 80kb, now FPROTECT...
Hi, I am using VS Code with Extension Pack for nRF and nRF Connect SDK Toolchain v3.2.1 and trying to build the environment for working with the dect_shell sample. nRF9151...
Hello all,
I'm using ble_wifi_provisioning example.
I need to save the phone pairing. I added the definitions as described here: https://academy.nordicsemi.com/courses...
Hello,
I am planning to conduct R&D on Bluetooth Low Energy (BLE) with PAwR (Periodic Advertising with Responses) and low-power communication techniques. To progress with...
I originally developed the product using the nRF5 SDK with C++. The functionality is already implemented, but due to high power consumption from the C++ version, I now plan...
Sadly not in the documentation and the sizes changes from 5.0.0. I did try using the 5.0.0 but it doesn't boot (could be another problem). Thought I'd ask anyhow.
I have managed to use 3 nrf5340 audio DKs one configured as Gateway and the other two as left and right headsets to stream stereo audio. My question is, what do I need to...
I’m working on an nRF52-based design where the device should remain in System ON low-power mode after an operation (SAADC sampling + BLE sync). After SAADC data collection...
Hello,
My application uses three nRF5340dk for LE Audio: two Unicast Servers and a Unicast Client. The Client scans for servers, establishes connections, performs discovery...
Hello, I'm using the nrf5340 Audio development kit with SDK Manager v2.9.0 and a micro SD card, and when I try to play the audio as indicated in the development example in...
Hi, I have the following situation:
I have a legacy C application that runs on the good old nRF5 SDK on NRF52840 with FreeRTOS. (No BLE on the application, but the bootloader...
I am trying to repurpose NFC1 and NFC2 pins for GPIO usage, but they do not function as GPIO, while other GPIO pins work correctly.
SDK: nRF Connect Bare-metal SDK v0...
Hi Team,
Below function returns error code as -5 and unable to write and read data from I2C peripheral.
err = i2c_write_read ( i2c_dev , addr , write_data , write_size...
Hi,
so i was using the NRF51822-QFAC with an external balun and this antenna chip 2450AT43A100E .
now i want to move to the nRF52832 chip and from what i read is that...
