hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,
I am strugling to program the Central uart example on the NRF52840 dongle and activate the VCP on USB.
I am using VS, nrf connect and SDK 2.0
Please advice
Br...
Hi,
I want to parse and encode JSON data and send it over Bluetooth.
I couldn't find any proper example project.
I have the following struct and description:
I can...
I am attempting use the Device Provisioning Service on NRF9160DK with Azure IOT hub. I am using the connect SDK version 2.0.2. I can connect to IOT hub and log messages without...
Hello,
I am working on an automated testing suite for our production.
Is ppk2 board supported by the "ppk_api" listed by this guide?
Do you suggest the "ppk_api" over...
Dear Nordic support team
I found that there were only ble keyboard hid and ble mouse hid samples in nrf5 SDK. A customer planed to use nrf52832 to develop a ble pen hid...
Hi Nordic team
At all Matter samples at ncs2.1.0 with nrf52840, after VS Code building, flash and RAM size were both over 85%.
So, insufficient size was left for user...
Hello
I need the code where i can get mac addresses of all mesh connected devices. Suppose <- this is the link to find only one connected device. Is it possible this code...
Hi
After updating to latest nRF Connect for VS Code i have an issue debugging my project with Ozone using the "Debug with Ozone"
With previous version the generated jdebug...
We are having difficult getting a R&S CWM500 to connect to our nRF9160-based device (operating in CAT-M1 mode). We are using a R&S test UICC. We have already attempted all...
We tested our project a while ago with nrf sdk v1.9.1 using the lte_ble_gateway sample (app on nrf9160, hci_lpuart on nrf52840 using a nrf9160dk board). Now we have developed...
The documentation says ...
The sample displays the following output in the console from the non-secure firmware:
SPP: send message: Success
SPP: process signals...
Hi,
I'm developing on the current setup:
nRF52833 DK, emulating an nRF52820.
Soft Device 113 version 7.2.0
SDK 17.1.0
IAR EW ARM 9.30
I'm trying to include...
Hello Team Nordic,
I am running a GNSS sample under SDK 1.9.0 and using modem firmware version 1.3.2.
I can get location without using A-GPS support but we get error...
The second instance of UARTE, UARTE1, was enabled in the configuration file. The receiving interrupt of UARTE1 failed to enter. Please help to check the reason
Hi everyone.
I am using nRF Connect SDK v1.6.1 (it's an old project) on a custom board with a nRF5340 on it.
The firmware is based on the central_bas sample project with...
