Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi,
I am performing several "mlme_reset_req()" on a nrf52840 during runtime without problem, for the most part.
However sometimes the radio stack will stop after a ...
Good day
I noticed that the NFC tag reader sample is not compatible with the nrf9160K. Is there a reason for this ? will development be possible?
Thank you!
Hi Nordic
I downloaded nRF5340 DK Hardware files (Altium Designer files).
pca10095_sheet1 and pca10095_sheet2 can be imported in PADS logic tool.
But, files from sheet3...
Hello,
I have a problem when I send data with CDC ACM and using CLI interface my data is mixing. If I put a delay between sending data I have no problem but this solution...
Hi, I want to enter the NRF52 into a standby low power mode.
I am running sdk17.0.2, with FreeRTOS and softdevice (7.2)
The steps I take are:
1) stop all my threads...
I'm trying to integrate the following driver into my project
https://github.com/nobodyguy/HX711_zephyr_driver In order to load it I need to update the west manifest. Using...
Hello,
I am working with the nrf52840 chip, and would like to store a serial number on the device that persists across boots and OTA-DFU. I have integrated the nvs sample...
Dear All:
We run a simple message model in light_switch_client and light_switch_server code.
After provisioning the two nodes via nRFmesh app and set pubilsh in clent...
Hi,
We need to refer detailed documentation & implementation for health model struct bt_mesh_health_srv_cb
we referred to this document - https://docs.zephyrproject...
Hi, This appears to be similar to Case 232209 (from 3 years ago).
What: I am looking to have the 9160 act as a producer - sending ANT and GPS records on a regular basis...
I have a problem to advertise a service. When I include a header file, an extra service is automatically created. It seems like that the service will be advertised twice....
Hi,
I managed to do a DFU with an application on a nRF52820. Now I wanted to test if I can also update the softdevice. For this I read the following article: infocenter...
Dears,
I am developing a device base on nrf52833 SOC, nrf Connect SDK ver2.0.0.
I run the bluetooth mesh sensor server example and I want to have OTA on it.
But when...
What is the maximum time that I can use in app_timer_start?
I tried setting it to APP_TIMER_TICKS(15 * 60000) in order to set a timer of 15 minutes but it timed out after...
