Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Dear all
I am developing a BLE product, and would like to have a different device name for each unit like Product1, Product2 etc. when advertising, so user can identify...
Hi! We are updating our application from NCS 1.9 to NCS 2.1. In the documentation of the HTTP AT command of the 2.X versions of NCS the XHTTPCRSP notification is documented...
Hi Nordic,
1. I am planning to do DFU update with UART
2. I Build smp_svr and flashed successfully when am using mcumgr its getting NMP Timeout
3. I added CONFIG_MCUMGR_SMP_UART...
Hello,
In my project, I have a device (nrf52833 custom board) which I want to operate in dual role (central/peripheral). I've followed a ble_app_hrs_rscs_relay example...
Dear Sir/Madam,
We developeted a smart device based on nRF52840 chipset(to be more accuracy, we desgined our own module based on this chipset, then our end product use the...
I'm currently trying to change the host name of "https_client" and check the operation, but it doesn't work.
Even after changing the host name back to the original, "Waiting...
Hi,
We want to do provisioning of multiple mesh nodes using pb-adv procedure. we installed nrf MESH app, but we are not able to do provisioning for one node using Pb-adv...
Hello everybody. I'm designing a custom PCB fed by a typical 3.7 V nominal 4.2 V peak lipo battery, where minimal area and thus component count is a key factor. Aside from...
How can I adjust the BLE transmit (Tx) power, up to and including +8 dBm? I'm using nRF Connect SDK (NCS) on an nRF52840-DK .
I modified the throughput sample to reverse...
Hello, I'm trying to run the Ble Peripheral sample from "nrf\samples\bluetooth\peripheral_lbs" i'm using nrf connect V1.8.0 and NRF5340dk i followed the code in the github...
Hi,
I'am using the Ultrasonic Oxygen Senor with the nrf5340, the output is like this "photo" I want to calculate the concentration and the purity and with this values I...
Hello,
Is there any way to program the frequency output when sending a carrier wave to have a step size of around 1KHz? It seems that the default step is 1MHz.
Hi
I am trying to get the manufacturer data by ble_advdata_parse() as instructed in this case and this case , but it's not found in my SDK14.2, so how can I get the manufacture...
It's not possible to proceed a firmware update of matter light switch example on nRF5340DK.
I use following SDKs / Repos
nrfConnect SDK v2.0.2
standalone zephyr SDK...
