i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
What do I have to set in order to require a new passkey every time I connect with my nrf52dk_nrf52832 build?
I have tried to prevent bonding using bt_set_bondable ( false...
I am using the PPK2 kit to perform current measurements of our system and what I notice is that after a couple of minutes the program becomes very sluggish.
When I open...
Hi, We are using nRF9160 on our custom board. (SDK 1.9.1) with "serial lte modem" firmware. We have two external antennas for GPS and LTE. Now we are implementing location...
i devzone
I following the blog ( devzone.nordicsemi.com/.../testing-max-range-with-ble-with-nrf21540dks-and-nrf52840-dks) to setup 20DB on 21540 DK (pca10112), it is works...
Hi,
I was trying to turn off logging in zephyr\subsys\usb\class\cdc_acm.c, by setting LOG_LEVEL to 0, but when I do that the logs are still printed on the console.
First...
I added custom module to default asset_tracker_v2 to upload custom data to AZURE_IOT_HUBuisng nRF9160DK kit. All the functions are working well. The default is getting transferred...
The iBASIS SIM card I received with the Thingy:91, during activation, I got an error message that the SIM card is expired. I contacted the iBASIS support and I got a new SIM...
Hi everyone,
I'm currently doing some experiments with the zigbee feature of NRF52840 and I'm working with an PCA10056 development board.
The light_bulb example however...
Hi,
I'm so confused about UART error when I enabled DFU and download bootloader.
In my application, UART worked normally when disabled DFU, but logging ERROR 1 after enabled...
The provision button in nRF Mesh is no longer active. It worked yesterday but I think there was a update to the app and it no longer works.
The app finds the unprovisioned...
Hello all,
Four leds are connected to the GPIO (22-25) and gpio are defined and with a simple method within the while loop I can see them working
Next is to use the...
Hi, I am developing nRF52832, ADS1291.
I got the data from ADS1291 normally through SPI communication.
And I applied RTOS by referring to the nRF5_SDK_17.0.0/examples...
Hi,
Is there a way to turn off the reset loop detection on MFW 1.3? It's annoying having to wait half an hour when you are developing...
Kind regards,
Thomas
My product is devloping in nrf52810 with Zephyr . The flash is too small. At present, using all peripherals, the size of app_update.bin is 55KB. The size of MCUBoot partition...
