I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi all, I am using the nRF52832, Mesh sdk v4.2.0 and the nRF5 sdk v16.0.0. How to dynamically change the GAP name of device when using smart phone (nRF connect APP)to scan...
Hi, I'm following the steps on https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_gsg_ncs%2FUG%2Fgsg%2Ffirst_test.html
But in Programmer, the read, write, erase&write...
Creating a second advertising set with bt_le_ext_adv_create will generate an error -12.
Using nRF Connect SDK v1.8.0
The second advertising set is use for FOTA update...
Hi all,
i'am using nrf_Connect_sdk when i write this api
device_set_power_state(); it gives me undefined symbol
i enable CONFIG_TICKLESS_IDLE =y in prj.conf it gives...
Hello,
My company is evaluating the Thingy:91, we're interested in Multicell location lookups. My question is regarding the SDK, specifically if it's possible to configure...
Hi, I am unable to download my program and there's no detailed error messages, if any at all. Can someone please tell me what's going on?
Load "C:\\projects\...\\nrf52832_xxaa...
My company is creating a custom board using the 9160 and 52840. I have a BLE app running on a nrF52840 board that I want to port to the 52840 on the 9160 custom board. And...
I'm a newbie (few weeks) with nRF9160-DK and using nRF Connect SDK v1.7.1 / VS Code on a Windows 10 PC
Good afternoon,
I'm struggling with how to set up and start the...
Setup:
- nRF52832 , Softdevice s132, gcc
- iPhone is the peripheral. A custom service is implemented **on** the iPhone.
On the nRF:
- `#define NRF_SDH_BLE_VS_UUID_COUNT...
Hello.
We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
I am creating a function to connect to a central device, have the characteristic set...
Hi,
I am flashing Blinky led hex file on the flash at 0x5E000 location.
And again if i try to flash the different Blinky hex file at the same location. it wasn't working...
Hello,
I could use some guidance on where to look for a power draw that I am not understanding. I am not a hardware engineer but have been tasked with completing firmware...
