We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi,
I need to use system tick to do some math calculate. So I create a new function to get systick like as below. then I can get some number.
And I create a 200ms timer...
Hi,
I'm new with BLE development and I'm trying to find a module that can be used with an Atmega328p and libraries that allow me to create a GATT profile (creating services...
Hello, everyone.
I'm beginner at this, and I need your help.
As the title says, which of the GPIO pins can be specified for PWM?
I am waiting for your answer.
Dear Members,
I want to run :
E:\nRF5_SDK_17.0.2_d674dde\examples\peripheral\spi\main.c
on this line :
APP_ERROR_CHECK(NRF_LOG_INIT(NULL));
I get :
error ...
Hello, I have an application using nRF5 SDK 17.0.2 and SoftDevice S140, I would like to implement the mesh function on my devices and I have some doubts.
1- What is the...
I tested it in a conductive way. The transmission power of +8dbm is set on the software. Remove C3 and L1 and connect the RF line directly to the ANT PIN to test the transmitted...
Trying to understand how interrupts work on nRF52: does setting an INTENSET register of the said peripheral enable the interrupt, and to propagate the interrupt over the Cortex...
My operating system is window 7, and I have been using nrfjprog v10.12.2 before. When I updated nrfjprog to v10.15.0, the following error occurred when using nrfjprog -v....
Hi there,
I want to run FATFS example but I got this error ?
========================
nfo> app: FATFS example started. nfo> app: Initializing disk 0 (SDC)... rror> app...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I found that the maximum clock frequency of nRF52832 is 64MHz, but I don't know what the current clock...
Hello,
I know there are dozens of threads on this topic already but they don't seem to quite answer all my questions.
Some background:
SDK: 15.2
SoftDevice: s140_nrf52_6...
I am encountering the following error when trying to build the Asset Tracker code. I have tried uninstalling everything and reinstalling it and the issue is still there. I...
nRF52832, SDK 13.0, no Softdevice
I had a possible power leakage issue and tried to debug it with Segger Embedded studio.
Please refer to below.
int main(void) ...
Hi,
(nRF52840)
I have project made in SEGGER Embedded Studio with OPUS Encoder (optimized by Nordic). It's CELT, bitrate 40000 and complexity 5. This is configuration...
