I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi, Dev Zone.
thanks for help : )
i'm try to porting DK Board's ble Boanding function to Target Board.
DK is working success.
refer to 16.0.0 SDK and 7.0.1 Soft...
Hi,
I am currently working on updating the examples/dfu/secure_bootloader_uart_debug example in SDK 15.3.0 to do an internal dfu on my nrf52840 DK rather than having the...
Hello,
Out application is using the time slot api to generate ~29ms (35Hz) burst of pulses.
Occasionally, the interval between two adjacent pulses extends to ~35ms ...
Dear Nordic support,
I need to clarify a few points using SAADC for battery measurement - running the ble_app_proximity application without modification. I measured the...
hello, i hanve a problem when i use usb transfer data to pc with ep1, sdk 17.0,nrf52840dongle
I have many data(more than 100KB) transfer to pc,when I send the data for once...
Hello,
I am using the nrf52840 for the application, basically i want to use the timer driver in my code.
so basically if i have 5 timers of nrf52840 and i am using one...
I am using a nRF52840 Development Kit to flash a custom board with a nRF52840. When I use the nrfjprog -p (or --pinreset) option to reset the CPU, it will consume over 1mA...
I am using nRF52833 on ncs to turn on the extended broadcast. After referring to the corresponding settings, I found that the transmit power setting does not take effect....
In standard sdk 17.0.2 is it possible to know which devices did i accidently disconnect?(Interactive command s140)
for example
my central is the interactive command...
Hi, I used NRF52 DK and NRF Connect SDK 1.6. I used the st_ble_sensor sample with no changes. When I press Button 1, I expect to get a notification on the central device....
Is there a straight forward guide that demonstrates how to changes the Asset Tracker V2 application from "Active Mode" to "Passive Mode"?
Referencing the notes on the application...
Hello,
I have been working with nRF52832 microcontroller on a custom PCB. Currently, we are implementing OTA updates through BLE, and developing using the nRF toolbox app...
Hi,
I am trying to program the nRF52 DK with external j-link Base. I am using Debug IN P18 connector and connected the following pins
j-Link base nRF52 DK Debug IN P18...
