I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Nordic NUS - uart service; both SDK 15.3 and 17.0.2. Packet loss on repeated BLE disconnect - connect cycles; seeking clarification of my understanding.
"If there are untransmitted...
Hi, teams.
I am testing nRFConnect 1.5.0 with nRF52833DK.
Recently, I noticed "Direction finding connectionless beacon" example in latest repository, and copied it to...
Hello Team Nordic,
We are using nrf9160 DK with nrf connect SDK 1.5.0 and mfw_nrf9160_1.2.3 modem firmware .
We are currently evaluating the FTP AT command set and according...
Dear Sir,
Moving to zephyr new installation 1.4.99
Configure SPI1,SPI3 . I can see the SPI configured in zephyr.dts
spi3: spi@b000 { #address-cells = < 0x1 >; #size...
Hi,
I am using the stts751 temp sensor with nrf52832 for temp data logging for short time. I want to save temp data in the internal flash memory but I didn't find any similar...
I followed the instructions in https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.3.0%2Fsdk_config.html
and pasted the appropriate text...
Hello,
I have been trying to get the ADC working but for some reason, the adc_read function throws an error of invalid argument ( -EINVAL (-22) ). The adc_channel_setup...
Hi all, I have tried to follow the step to get up and running with my new nRF9160-DK, however, I am not sure if the Application FW has been successfully updated (how would...
Hi,
We are using a bootloader/DFU based on the secure_bootloader example with USB transport from SDK15 and It works fine.
Now, we are trying to add the possibility to...
hi.
i use nrf52840 to d evelop a keyboard .i connect and be bonded by a pc,now i want to delect to the bond info of the pc,and after this ,my adv cant be scan by this pc...
Hi Nordic Tech Support team,
One of my customers is having some problem with UARTE implementation. They used the ble_app_uart example ( pca10056 with SoftDevice 113 )...
Hello Everyone,
We are developing one custom device using open thread protocol.
We are using SDK - nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 and Dev-kit - nRF52840...
IN Establishing the friendship,I received the following error
/** The Low Power node was not able to send transport command due to internal fault. */ NRF_MESH_EVT_FRIENDSHIP_TERMINATED_REASON_INTERNAL_TX_FAILED...
I want to send ADC data over bluetooth. When I searched, I found the following contents.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsds_s132%2FSDS%2Fs1xx%2Fble_data_throughput...
I am using the nRF51422 development kit with the SDK 11. I am trying to run the proximity application located in ble_peripherals. When the project is build I am receiving...
