hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi, I have the Power Profiler Kit PCA63511 used on top of the dev kit PCA10040. I am trying to measure the power consumption of my custom hardware implementing nrf52832 using...
I'm already using nrf51 in a project and now I need to make a DFU with BLE using a gateway. For the gateway project, I was thinking of using a nrf5x to implement a DFU master...
Hi , a day ago i recived my first dev board from nordic semiconductors, the nRF5340 . Until now I only coded for AtMega328 , esp32, esp8266 and other microcontrollers like...
I am trying to build the aws_fota example project for the nRF9160 using the nRF Connect SDK and the Segger IDE. We currently have v1.5.0 downloaded. The project is not compiling...
Hello everybody,
i use two nrd52 dk boards with nrf mesh light server flashed on them (mesh sdk 4.2.0)
They are configured over nrf mesh app to be in the same network...
Hi, I have nRF52840 DK. How can set the max range? or how can increase/decrease the tx range? Also is there any range extender to improve range? Thanks!
Hi,
I am currently doing a uart dfu over 2 nrf 52840 dks on a Windows PC. I have been using the example found in ...\examples\dfu\secure_bootloader\pca10056_uart_debug supplied...
Hello,
I am porting the secure serial bootloader from the nRF52833 DK (PCA10100), in which it works fine, to my custom board. I press the button and turn my board on to...
Hello, all
Following this ticket ( Configuring ADC sampling rate and simultaneous reading from multiple channels. ), I found a great example code that sends readings from...
I'm using an nRF52840 Adafruit Feather Sense to communicate with a program on my computer over an OpenThread network. My computer is using an nRF52840 DK board as a network...
In other words, is it likely that the EasyDMA that's scheduled after the first HOST->EPOUT completes will copy bytes that have been overwritten by the second transfer?
I...
Hello,
My device based on ble uart app with nrf52832 operating with 2 AA batteries. It has 4 LEDs and 4 buttons. 4 LEDs are always on for indication but when a button is...
I'm blocked trying to get an Nrf52 application developed under v1.3.0 SDK work with FOTA.
My application is working fine. FYI, its on custom hardware derived from nrf52832_mdk...
Hello everyone,
I have a setup with two DK52 (nRF52832) with a mesh level client on one board and a level server on the other. Everything is working fine, no problems there...
