Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
As what I said in title , the answer I found was posted 5 years ago , and the interface is totally different. I just can't find where is the preprocessor selection . Can anybody...
In my device I send data using a characteristic with indications. The client sets the indication and data is then sent. I understand that when a device is bonded the values...
Hello,
In nRF52832 we use these commands to write data to user information configuration register:
nrfjprog -f nrf52 --memwr 0x10001080 --val 0x00010000
and use memcpy...
I had my environment running fine with (IIRC) SDK 1.4.x and Segger J-Link v688. I thought "it might help" to upgrade to the latest SDK.
I have the new SDK built and apparently...
Hello Use the S132 Central. Use two S112 peripherals. I want to communicate data to two connected peripheral devices at the same time. You are using nus. The connection was...
Hello,
I am working on a wearable device and need the lowest power consumption possible. The project configuration is:
S132 7.2.0
SDK 17.0.2
The board is powered...
Hi There
My design is basic on nrf52840. I need a pin be controlled alternately by GPIO module and PWM module in my application. The PWM function is realized by setting...
Hello!
I am now working on a customer board based on NINA-B3 module (NRF52840).
I found a weird problem: after successfully flashing firmware through SWD for several...
I was working in a Zephyr project and wanted to test something on my nRF52840-Preview-DK board - which I had just used minutes before and successfully had `west flash` write...
I'm trying to compile the serial LTE modem to trial the functionality.
The version as set by the import examples program in SES does not compile:
The error: mkdir(modules...
I set up PPI so that it kicks off TWIM (I2C) transfer on GPIOTE pin transition low to high. Everything works great, except that I also setup a fork task to set another GPIOTE...
Having a BUS FAULT while trying to use uart_tx on the NRF5340 with NRFConnect SDK. Based on the peripheral_uart sample project. Any ideas what may be causing it?
Heres...
This took me a while to figure out.
The default values for the WDT configuration in SDK 15.3.0 (and 16.0.0) is spelled as "NRFX_WDT_DEAFULT_CONFIG" ?
RMV
The following code has an unexpected out-of-bounds array access:
Primary cause is this line:
On an uninitalized pin number, channel_port_get() returns -1, which...
