Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hi,
this is my first time trying to use nrf connectivity tools, and my setup is a bit strage (and I have no clean DK setup to compare with:-(
I have to update firmware...
I am developing an IEEE 802.15.4 Application on the nRF52840 using the Radio Driver (v1.8.0) . I have a problem with the transmit call function. Very often in nrf_802154_transmitted_timestamp_raw...
I wrote a program for nRF51822 and compiled it with keil. The app, boot, and sdk are combined and written to the chip. However, if I write using nRF Connect Programmer, it...
Hello,
Our custom board (nrf52832, S132) seem enter to the read back protection, J-Link could not connect to the target in any ways.
We tried the command "nrfjprog --recover...
The code is running on 52832 (BLE) and transmit msg over BLE (NUS) each time GPIO is active (GPIOTE).
But same code (after adding LE CODED Phy) is crashing once it reached...
I am trying to build the NCS sample project "peripheral_lbs" with multiple peripheral connections. Therefore I added the CONFIG_BT_MAX_CONN. Up to 20 the build is working...
I have a problem when activating the simcard via nrf connect. |
After several attempts, using the IMEI and PIN on the Thingy 91 product, i get the following error.
(There...
Hi. How do I advertise both heart rate service and current time service together?
Seems like the current time service overwrites the heart rate service.
I will appreciate...
Trying to convert a working sample for a BME280 sensor from I2C to SPI
nrfConnect 1.4 on nrf9160-DK
After looking at other SPI examples and noting the syntax I thought...
Hi,
i have changed uart pins to second port. After that it is not advertising. when i connect the FTDI converter to the uart pads from custom board, it starts working and...
Dear Devzone Community,
when trying to get the Zephyr SHT31 Sample running, I stumbled across an error which I was not able to resolve.
I did the following:
Add nrf9160dk_nrf9160ns...
I need to control the BLE ON/OFF state and send some data to MK81 via BLE through UART, we have estalished the Hardware connection between the nRF52832 chip and MK81,
How...
So, I am quite beginer with programming and working with this sensors and nrf, So I need your guys help.
I am trying to get the x,y,z values from the accelerometer of BMX055...
The nRF 52840 RSSI "meter" is not usable.
I tested in an RF (2.4Ghz) quiet neighborhood. Using a reference receiver, I measured RSSI variance around +/-3 dB (95% confidence...
