Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
There are the following projects under the Health Thermometer example for Keil
What is the difference between them when trying to install on the nRF51 DK? I could not find...
Two (2) nRF52840 DKs, SDK 17.0.2
I believe I have added the necessary code from ble_blinky_apps both peripheral and central to their respective NFC reference role examples...
Dear Sir/Madam,
I'am new to segger embedded studio.I would like to do SPI interfacing of an IC using nRF51822 with segger embedded studio.
Please guide me how to add...
Zephyr version: 2.4.99
OS: Linux
Board : nrf9160dk
I am trying to read data on UART 1 with interrupt. I have below shown portion in my code for enabling UART 1. (I...
Hi, I need to Interface the 2.4" SPI TFT Module ILI9341 Driver with nRF52832
I came across that in Peripheral/ GFx Example will run. once I build and run the project My...
Hi Dev Team,
I was working on the Nordic Thingy91 and had to establish an external communication of a sensor to the Thingy91 through a UART.
For this, I was looking into...
Hi,
My PC is Windows 7 64-bit and my tool is J-Link V9. The CPU at my target board is nrf52840. I use nRF connect desktop version 3.60 and it works fine. I got the upgrade...
I have the driver setup like all of the other sensor drivers I'm using, but I can't seem to find a device tree or Kconfig
This should be enabled by the CONFIG_SOC_NRF52840_QIAA...
Hello!
We have a custom board connected to a battery and a USB cable
Our fw calls:
NRF_POWER -> SYSTEMOFF = 1 ;
The board turns off.
And then we remove the USB...
Nordic's smart remote 3 is for nrf52832 and nrf52810.
I want to port the same on the nrf52840 DK.
I have basic IR receivers and Transmitter and want to integrate them...
I'm using the nrf52832 from fanstel (bt832) to stream audio to the adau1701 dsp. I want to be able to play music over Bluetooth. I'm using i2s to transfer the data to the...
Hello,
I am trying to change PHY after packet sent/received (known as asymmetric PHY).
After receiving EVENT_END, i write to register MODE to change the PHY.
This can...
Hi ,
I am using saadc to measure battery voltage i m using the sample example given as reference ble_app_proximity/
I am doing adc_configuration in one file and triggering...
Hello
I am starting with nRF 9160 DK and Segger Embedded Studio, I installed Segger through toolchain, the activation sim, updated of certificated and connect the DK to...
