Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Can i use 2 nos NRF52832 BLE chip on single PCB , PCB size is 30x50 mm ,
1 chip for scanner
2 for advertising
3.If yes what is the position for antenna of both Chip...
Dear technical support.
We are using this chip (nRF52832) in our hardware.
I'd like to check is this feature AoA(part of BLE5.1) enabled in the chip?. Is there any application...
We are designing a people location tag for building workers. Bluetooth direction finding AoA/AOD is good for the application. Is there any development broad for Bluetooth...
There is a potential for the NRF_MESH_ASSERT(m_reliable.next_timeout_index < ACCESS_RELIABLE_TRANSFER_COUNT) to fire on line 170 of access_reliable.c if the following conditions...
Hello,
I am trying to install the pc-ble-driver-py for my buildroot arm-board.
After some struggle I was able to compile the pc-ble-driver for it, however the python tool...
Hi guys,
I am working on my project and until now I enabled the device to measure the voltage and get the sensor data from the temperature sensor which I need now to send...
Hello,
We have been using FDS in our nrf52832 based product. Recently we had a need to port application to nrf52810. It required some flash memory optimization. Fortunate...
Documentation states “When a connection is created it will inherit the transmit power from the initiator or advertiser leading to the connection.” In my BLE event handler...
Hi,
SDK16
I'm using ble_cus.c to define custom BLE service.
In the ble_cus.h file the definition of the UUID is
#define CUSTOM_SERVICE_UUID_BASE {0xBC, 0x8A, 0xBF...
Using just the nRF Connect SDK, I cannot get a push button to interrupt the NET CPU on the nRF5340DK.
I have the following code on the APP CPU:
nrf_gpio_pin_mcu_select...
L2CAP connection oriented channels can be used to transfer frames of up to 65533 bytes. L2CAP is a record oriented protocol. When receiving L2CAP data, using the softdevice...
I have purchased eval kit and entered bootloader mode by pressing BOOT/RESET button while powering up the device but haven't put any file but now when i power up the device...
Hi,
We are in a stage where we want to perform certification of a product and are now looking into an application that can be used to this end. The board is using SDK 15...
Hi,
I've bought a nRF52840-DK kit to evaluate a Nordic BLE SOC (we are interested in using the nRF52811). I've installed SEGGER Embedded Studio 4.52, and obtained a Nordic...
