Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
I am facing a strange situation with my app. After turning off all my peripherals and switching to the most minimal code, I see quite a lot of current consumption and that...
So I'm completely new to bluetooth and I've been trying to set up the nrf52 dk pc 10040, but I can't seem to find any recent tutorials to set it up and I don't know where...
I am running flash_fstorage_example on the nRF52840 DK with SDK 15.0.0
I am having some problems with the example, as below:
1. When I run the example and use the shell...
Hi, I am trying to do MQTT disconnect, but I am always getting an error. First I successfully connect to the MQTT server, then I send some data, and then I want to disconnect...
Hi, I've been trying to use the nRF52840 Dongle to act as Bluetooth 5.0 peripherals but I cant seem to configure them for Long Range (coded PHY) detection. I am currently...
I ran one of my 9160 DK boards for 10 days using the Asset Tracker demo. The Hologram SIM card site I used says data exceeded 1 MB, which I understand the limit. Although...
Hi,
I have been trying to print out the float values using the NRF_LOG_FLOAT_MARKER, and i am only able to print 2 values in a single NRF_LOG_INFO line. Is there a way to...
Hello! I'm following the nRF52 Dongle programming guide to adapt the USB examples from SDK 15.3.0 to the nRF52840 Dongle. USB CDC ACM works fine, and I managed to get half...
Hi,
Sorry to bother you in your holidays.I want to get an conversion every time by calling nrfx_saadc_sample( ) .So I had configure saadc like below.But I found the adc...
Trying to print floats with NRF_LOG functions always prints a value of 0.00000.
E.g.
float value = 123.456; NRF_LOG_ERROR( "Float %f\r\n", value );
prints:
ERROR...
when I try to run: pip3 install -r mcuboot\scripts\requirements.txt, it fails with the following;
Collecting cryptography (from -r mcuboot\scripts\requirements.txt (line...
I'm trying out DFU functionality using nRF52840-PreviewDK and UART transport
On this page there is a table listing all the different combinations that can be downloaded...
Hi everyone,
I am currently working on a project that requires ICM-20648 and nRF52832. Is there an I2C driver available for these devices? The end goal would be to display...
I am using Keil and nrf52 dev kit to write some UART over BLE code if I set a break-point in nus_data_handler() it cause a reset to run soon after stepping though some code...
Hi to all,
i am developing an product based on the nrf5240 soc and i want to implement an hid device. after receiving some commands from HID i need to gather user presence...
