i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
I'm trying to listen to a bluetooth low energy connection between a smart bracelet and my smartphone. In Wireshark 1.10.1 I only can see the Advertising Indicators. As soon...
We are able to run both these services (experimental buttonless DFU and experimental app ble blinky) individually in Eclipse GCC, SDK 12. However, when both of the services...
I am intended to integrate the Nordic SoC nRF52832 in our PCB to generate a PWM.
However, I could not understand the difference between the following:
topicSchematic QFAA...
Hi to everyone, i have the mpu6050 code and i have to change it with parameters of adxl345.
i have this definitions:
#define ADDRESS_WHO_AM_I (0x75U) //!< WHO_AM_I register...
Hi, I am trying to connect a peripheral device which in this case is a BLE device called DELTA and I am trying to connect it to a central device which is the NRF52 board....
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
In nRF5_SDK_12.1.0_0d23e2a in file: ...\components\softdevice\common\softdevice_handler\ant_stack_handler_types.h In lines 30-32 inside #ifdef ANT_STACK_SUPPORT_REQD is preprocessor...
Hi ,
I have nRF51822 beacon and J-Link LITE and i am using nRFgo studio setup .I am trying to flash the hex file in to the beacon using nRfgo studio.The beacon has two...
Hello!
The DEC2 pin is connected to an N.C. capacitor C6 in the newest refreance layout and the nRF52 DK layout. So does it mean I can just left it DNC like the 44th pin...
Hi,
I have a custom board of nrf51822 with no external crystal, neither 16 Mhz nor 32Khz. I am trying to use uart and app timers from SDK11 but when I start any app timer...
I'm in a situation similar to the one described in this question:
devzone.nordicsemi.com/.../
The company performing the test ask me to provide a device that can switch...
I wanna execute rtc0 on the project which is inside examples\ble_peripheral\ble_app_uart file in sdk 11
When i write the following codes ,nrf51 is locked.bluetooth connection...
I created a characteristic of 20 byte length in a peripheral.
when peripheral does indication, the length of indication data in central is always 20 byte.
I want to send...
I'm porting from sdk10 to sdk12.1 and changing to .zip based libraries in keil5. I've unzipped the sdk into the directory and the examples work fine. However, if try to copy...
