I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi
I'm trying to use the nRF Cloud Provisioning Service with the nRF Cloud multi-service sample in SDK 2.6 on a nRF9151DK.
I have got the token from the device using AT...
Hi,
Do you have sample ios reference code for app that I can start developing?.
I have been searching the web and couldnt find a good example. basically for updating firmware...
I use ncs v2.7.0.
I am evaluating to connect 250 nodes in BLE network . Each node sends BLE packet periodically for every 100ms.
In project sample, periodic_adv_rsp.c...
Hello,
I am running the SDK on Fedora 41 Workstation using VSCode (Codium) with NRF Connect SDK Extensions. Everything was working fine with v2.7.0 SDK installed using the...
I am having nrf52840 dongle,my purpose is to make it a peripheral device,enable gatt,change tx power through gatt.i uploaded blinky hex code(compiled in vs code ) to the controller...
I am using nRF52833DK, zephyr v2.7.0.
I want to disable hardware nRST to use P0.18 as GPIO.
What I did
Added to Kconfig : CONFIG_GPIO_AS_PINRESET=n
Removed : gpio...
I previously tested the peripheral_ams_client with iOS 17, and I could select the device in iOS Bluetooth settings to connect to it, however it appears in iOS 18 iOS is not...
Dear: We have product using nRF51822 with BLE to UART bridge between an app on the phone and the UART interface on the nRF51822 device. that include control command and OTA...
I want to implement a PWM up/down ramp that preferably runs with no CPU involvement. From the datasheet it seems I can do this by storing a sequence in RAM and having the...
Programmer tool v3.0.9 outputting the error - " Failed to detect device after reboot. Timed out after 10 seconds." After the user attempts to write a blinky hex file to a...
Hi,
My Development Kit is PCA10040, SDK_17.0.2.
I have builded the example code -> \nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040\s132\ses
in...
Hi, I have multiple nRF52840 Dongles and need to set one of them to permanently stay in advertising mode, even if a device disconnects.
If I use the nRF Connect tool to...
Hi,
I click on the device tree editor icon in VS-code and I see nothing
although I have an open working Zephyr nrf connect application in VScode.
I installed nrf...
Hello DevZone,
I'm building a Matter development environment with OTBR and CHIP-Tool:
NB: Ubuntu 22.04 with WIFI and BT, get CHIP tool from official pre-built (V2.5...
I am trying to install the nRF_Connect_SDK and associated toolchain under Linux Ubuntu ARM64. I find from other postings here that nRF_Connect_For_Desktop is not available...
