I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello, I have one smartphone with Android and one ith iOS with NRF connect application and I can't see, only on iOS, the Primary and secondary PHY used by my advertiser device...
Hi everyone,
We have devices using the BLE module (nRF52) deployed in clinics for testing. They have been functioning without issues until recently when we noticed occasional...
I'm using the nRF54L15-DK to run a Bluetooth peripheral_hr project in DCDC mode, but if I write
nrf_regulators_vreg_enable_set(NRF_REGULATORS, NRF_REGULATORS_VREG_MAIN,...
Context: I am working on a project to monitor up to 880 devices in an Industry 4.0 warehouse. The warehouse is divided into 16 areas, with each area housing 30–55 devices...
Hi everyone,
I’m a complete beginner and need some help. I’m working with two XIAO nRF52840 Sense boards: one as a central and the other as a peripheral. My goal is to send...
Hi,
I am trying to use a digital channel to sync with a current measurement. I have connected VCC, GND and a digital output of my DUT to the PPK2. I can see from the scope...
I am evaluating a Fanstel BC805M device, which uses the nRF52805 chipset. I am using VSCode and have installed the nRF Connect Extension Pack, toolchain v2.8.0, and SDK v2...
I programmed a nrf52840dk board (PCA10056 3.0.0 2022.7 1050288497) as a sniffer. It works well.
Now I want to flash it to zephyr samples/basic/blinky by "west flash". west...
Hi,
(nrf52840, custom device, nRF5_SDK_15.3.0_59ac345)
I am working on a BLE project involving one central device and two peripheral devices using BLE NUS. The peripheral...
Issue with debug on the PDK eng_rev_B PCA10156
Segger does not recognize the chip and debug fails across multiple sample applications
debug message results:
JLinkGDBServerCL...
Hello,
We are investigating a compatibility issue between our devices running nRF5 SDK 12.3.0 with softdevice s332 v2.0.0 and a Motorola Edge 50 smartphone. From BLE sniffer...
Hello,
Does the nRF54L15 have multipoint?
In my application, I would like to have different devices connected simultaneously, so I was looking for something like multipoint...
Hello,
We have a Nor flash connected to the QSPI and another peripheral connected to the classic SPI.
Due to the errata [159] , the HFCLK128M is running at 64MHz and...
In the nRF9151 Product Specification, there are maximum gain requirements for the LTE antenna implementation, specific to supported bands. It is my understanding that any...
