Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
Hi
1.
A. nRF7002 DK(NRF5340+NRF7002)
B. Our PCBA(NRF5340+NRF7002)
We found same application code flash to both. Sample A can work. Sample B can't work and stuck
...
Hi,
I was previously working with W25Q32JVSSIQ, a 32MBit memory device communicating with nrf5340 chip. The QSPI driver was initialized using NRFX_QSPI_DEFAULT_CONFIG()...
Hi,
I’m working with an NRF5340 device paired with a Nordic HID mouse. Currently, data encryption is enabled after pairing, but the encryption and decryption modules are...
Hi,
I want to know if Android Smartphone can be configured as BLE Mesh node? If it can be configured as BLE mesh node, how can it be done using below mentioned library...
Hi.
I would like to set the TX power level for broadcast streams to a higher level then the other radio packets (especially the packets on the primary ADV channels). First...
Hi,
I'm working with nRF5340 Audio DKs.
I'm able to successfully run the audio example in BIS mode (with gateway and headset devices).
My goal is to open another BT...
Hello,
I am developing a PCB with nRF52805. The PCB is small and must be cost-optimized. It also needs to be as small as possible.
For prototypes, I have added a J-TAG...
I was building the "console" sample code found in zephyr for my custom nrf52840 board and I managed to get it to work. But as soon as cryptocell gets enabled, it doesn't work...
Hello,
I need to run nrfutil on a raspberry pi3. The NRFutil executable I use on windows & linux found at https://www.nordicsemi.com/Products/Development-tools/nRF-Util...
I have new nrf9161dk that I'm trying to run the "quick start" guide for. However, when I get to the "Progam" step it fails. This is the error log: 2024-10-03T18:05:08.932Z...
Trying to put nRF52840 in OFF mode and I see the following odd behavior: If I put all the output GPIOs into Hi-Z mode, power consumption measured in-line with the battery...
Hello,
Do the micro controllers out of the box before installing onto a PCB already have a bootloader? What do I need to consider to be able to reprogram my MCU on the PCB...
I'm working with the nrf9160 dk and trying to get a baseline low power project before I add peripherals and application code. I'm using ncs 2.7, and with an empty project...
The idle power consumption (i.e. the current draw between adverts) is 2.4uA prior to the first call of dm_request_add() following reset.
Once a distance measurement has...
Hi, I am actually newbie to embedded system.
My question is how can I upload my code to MCU.
There are very good tutorial about developing with development kit.
So...
