Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi.
I start SPI as well as I2C at the same time . then build code , the build error is occur . below is error code .
The SPI and I2C cannot be used at...
Hello,
I try to building sample code nrf_dm for nrf5340DK, but I got failed massage:
.7.0-rc2/nrf/subsys/dm/dm.c.obj -c C:/ncs/v2.7.0-rc2/nrf/subsys/dm/dm.c C:/ncs/v2...
Good Morning
Im using Zephyr, SDK2.6, toolchain 2.6. the peripheral_uart example is flashed to a 52840DK. when I connect with my phone IOS NRF_connect I get the error
...
I run the LWM2M client and send the data to the server. Nrf7002dk connects to the internet via wifi. Now I would like to update the software but I can't seem to do it. The...
Hi, I want to implement OpenThread features with another sample and I'm not sure how to go about it. Is it even a good idea to add OpenThread to another sample or is it better...
I use the serial port routine SDK17.1, nRF52833 want to burn the protocol stack, s113_nrf52_7.2.0_softdevice. But when I burn it to the chip, the address is 0x1000 and if...
Hello I have a board that I am trying to profile with the power profiler kit 2 and the readings seem very wild. I have a device that I know the base configuration with the...
I have a customized PCB with nrf52840. Pin 0.18 is used as CS pin in SPI communication.
I want to disable the nreset function and I add this CONFIG_GPIO_AS_PINRESET=n in...
I'm using the CLI interface through USB and UART, and I am wondering if there are any innate methods for checking the validity of the data being sent and received via the...
hi Nordic support team,
I cannot re-flash firmware for nrf52840 after ram off is implemented.
I recheck with other chip like nrf52833, it have the same result: \althrough...
I understand, it is possible to add variables to a section of ram, that will not be initialized (zeroed) at boot (see for example: https://github.com/nrfconnect/sdk-zephyr...
Hello,
I want to create my own board from the nrf52840. I am planning to copy the schematics given only taking into account what I need. I went through the schematics and...
Hello,
I am using the nRF51822 with SDK v9.0.0, SoftDevice S110, and the DFU bootloader v8.1.0.
For certain reasons, I want to reserve one page of the 'app data' for shared...
Hi Support Team
If a center role and a peripheral role in one nRF52840 at the same time，can the center role use code PHY and the peripheral role use 1M PHY？Many thanks.
Hi,
I need to read the data from an acceleration sensor. I tried with a custom program of mine to simulate some data, but it is delaying too much.
I tried reducing the...
