Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
Hi,
Sorry for the very basic questions. I am new to nRF connect SDK.
I want to develop a ble custom central application with my custom characteristics. I started to look...
Hello!
I have an application using MCUboot and a single application slot. I want to use the Retention System to signal to MCUboot wether to boot normally or into serial...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am using two nRF52840...
I b ought three ebyte E104-BT5040U USB dongle but it doesn't work.
I was program a ebyte E104-BT5040U USB dongle using openocd。I use daplink (2023-8-24) and openocd 0...
I've been playing around with the advanced_non_blocking_internal_timer example, on my nRF52DK-52832 board using NCS 2.6.0.
I couldn't get it working for what seemed like...
Hi,
I want to know how to use extended broadcasting in nRF5SDK.
I have tested the Broadcast Multiple of NCS2.6. The maximum extended advertising data length is 31 to 1651...
Hi! I am beginning development on my first BLE project using nRF Connect SDK in VSCode. I have done a few projects using the old nRF5 SDK. I am wondering what is the best...
Using VS Code, I've tried to build the "BLE UART service" (= peripheral_uart) for the nrf52840dk_nrf52840 board. According to the documentation, this board is supposed to...
Hi. I had a working MCUboot configuration that I used in order to update both the app core and the net core as follows:
- Upload the app core image using mcumgr - Upload...
I am working on a project that uses nRF5340.
We are now looking into designing software update mechanism. As a part of this, on the app core I am planning to move slot1_partition...
Hello,
when creating a multi-image build is it possible to select the optimization level for each image individually?
Below is an example of the issue I am facing currently...
Setup:
nrf connect sdk version v2.1.2
board: nrf52840DK
Trying to send a beacons for half a second whenever I get some specific data on uart, and also send data over...
I have an array of LEDs on my custom board. One of the LEDs is set on a UART0 RTS pin, which is GPIO(0,5), and we are using ground as common. To avoid any conflicts, I disabled...
I am using an IMU sensor in sensor hub mode (LSM6DSV16X, LIS2MDL) with the FIFO interrupt interval set at 30 Hz. The data is sent over BLE. It works perfectly when using RTT...
I am using the s120 soft device v2.2.1 as a center communicating with a peer using a s110 soft device.
The peer is a black box an all I have is the documented protocol. ...