I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hi,
I am trying to migrate my project from 52832 to 52810, somehow i found the services can't be discovered. And seems that on phone it's looks like it is connected, but...
Hello,
how to activate the Early Release Assistance Indication, to bypass the RRC_CONNECTED state.
This page from Telekom suggests that the user can do that to save much...
I saw in some post smart Bluetooth can have 7 active device. I would like to know what is the maximum number of Bluetooth devices i can pair up in sleep mode? i am doing a...
Hi,
I'm using SDK v17.0.2 on my nRF52840-based board. I have implemented buttonless secure OTA reflash and it generally works. When I get the NRF_PWR_MGMT_EVT_PREPARE_DFU...
We have some dev code where the workflow is as follows:
1. an engineering version of firmware is loadded to target. The target is erased then programmed in the normal way...
Hello,
I am using nRF9160 dk for prepare a program to I2C scanning for address. Can any one give a guide for start this task. Moreover, I am using Zephyr kernel on nRF9160dk...
Hello,
I want to read external accelerometer on nrf9160dk using I2C. But when I connect SDA and SCL pins of sensor to nrf91, there is no output.
The Code is:
When...
I am trying to set the UUID definitions for the Windows Application Bluetooth Low Energy 3.0.0. The only doc availible is for v2.3.1.
I tried to follow the following steps...
I'm using nRF SDK 12.2.0 and the corresponding soft device. I control a I2C slave for which I use the TWI peripheral through the driver implemented in nrf_drv_twi.c. It happens...
Hi,
I trying to enable Hardware Key for mcuboot.
I do the following at mcuboot.conf
CONFIG_BOOT_HW_KEY =y
But I got the following error:
Do I miss something...
Hello, I test SAADC on nRF52810, when I short gound to AIN0, the output is 0 normally, and when I add nothing to Pin I0(AIN0), the output is around 1056(Figure0), however...
I'm using nrf52833 on custom board.
And I need to using RESET pin to GPIO for battery charging detection.
I found CONFIG_GPIO_AS_PINRESET is configuration RESET pin...
Hi,
This may be a basic question. I'm using NRF52840 DK and I'm trying to print some logs from timer callback function, however I havent been successful so far. Here is...
