I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hello
I have this firmware running in C:\Users\danie\ncs\v1.5.1\nrf\applications\tracker on the nRF9160-DK, nRF9160 SICA B1 is the marking on the chip
Modem FW is...
Hi. Some questions regarding the nRF9160 ENABLE pin:
1. According to the nRF9160 product specification the ENABLE pin voltage requirements are like this:
In the first...
Is it possible to add additional UI for different sensors in nrfcloud platform ? I could see that there is a predefined list of sensor types that can be attached to cloud...
Hi,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK_v5.0. I would like to measure the time required to send a message from client to server...
Hi all,
I'm working on this example: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_tz_v3.2.0%2Fthread_example_dfu.html
I'm struggling on the server part, I...
Hello,
we are developing a verry small sensor node. Since we like to know if the sensor we are connected to, is one of our sensors instead of an attacker fake sensor we...
Hi! I was testing GPIOTE with pin_change_int example and tried to add a log to the push of the button.Somehow the code is not working, it is indeed changing the state of the...
nrf52840, sdk17. pca10056 (for now). linux arm-gcc, gnumake, etc.
I have a fairly complex PPI configuration but in the act of debugging it, I've dumbed it down quite a...
How does the interrupt latency compare between COMP/LPCOMP and GPIOTE? Are t LPCANADET and t PROPDLY the correct field to be looking at in the specification? The electrical...
Hi Nordic Team,
My Board: nRF5340 DK; SDK: nRF Connect SDK v1.5.0
I am new to BLE developement. I am trying to design a GATT service which can be accessed by nRF Connect...
I'm trying to use UART flow control and assign RTS CTS pin numbers.
What's the corresponding number for P0.02, P1.15 each?
And where can I find this information?
Hi,
I have used nRF52811 SoC in my custom design. In this circuit i have used SWD interface only as per reference design. I have used same SWD 10 pin connections as mentioned...
128 MHz or 64 MHz operation is mentioned in the specification (page ii). However, can MCU be capped at around 12MHz? How about the current consumption?
I am starting an experimentation effort with Nordic Mesh SDK. I am using Segger Embedded Studio.
I can open/compile/download the Mesh SDK examples.
I wish to start to...
Hi,
Hope someone can help with the following Q:
We are planning to make an new battery based iot sensor design based on NRF9160 SIP mounted on our own pcb with several...
