hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hello,
I am a newbie and trying to setup nordic thingy 91. I have booted the updated version of modem firm ware and also the "thingy91_nbiot_2020-10-30_5522ca2b.hex" file...
Hi Community!
I'm working on product development for a client/customer. The product will be a small embedded system with an LTE chip (nRF9160) and a BLE chip (nrf52840)...
I'm having a lot of confusion with using TWI on this chip. I have been running example code that I found in this tutorial nRF5 SDK - Tutorial for Beginners Pt 35 B - TWI ...
devzone.nordicsemi.com/.../nrf-connect-sdk-tutorial---part-1-ncs-v1-4-0 I follow the link above to create a hello world project, which has failed all the time. Here is the...
SDK16.0.0 + Mesh SDK 4.1.0
Help, we have developed our own board with a Fanstel BT840X module. Some of our boards are asserting ("Softdevice assert: 154516:0") and I am...
Hi Nordic,
I'm using nRF52 DK (PCA10040). I tried to copy and paste the project from this default location:
...\nRF5_SDK_17.0.2_d674dde\example\peripheral\twi_sensor ...
Hi,
I managed to compile and run(?) my first two programs for nrf51 dongle on Keil uVision, however while i think they run I cannot make the debugger work and see what they...
Any suggested APIs to setup BLE transmit power in NCS?
the set_tx_power() in the Zephyr example looks not work with nordic softdevice controller.
https://devzone.nordicsemi...
Hello
I am trying to compile a project for nRF25840 on a custom board. Build is succesfull but i am getting a 9mb ro-data on the output which means i cant flash it to...
Hi,
I am facing a problem in storing a 64 bit value to a variable.
some of the calculations which is resulting such a high values like this 4701924420
when i am trying...
Is there any way to use remote provisioning of nrf5 SDK example pb-remote in nrf Connect SDK?
If the answer is no, is the implementation of this feature in nrf Connect SDK...
I'm trying to test out the boot loader using the blinky sample. However if I add the following to prj.conf:
CONFIG_SECURE_BOOT=y
CONFIG_BOOTLOADER_MCUBOOT=y
I'm getting...
"SES > File > Open nRF Connect SDK Project..." does not seem to include a thread aware script for Zephyr. Is there a provided script for this somewhere? If not is there a...
Hello,
I would like to use a single COMP I/O pin to compare the pin voltage to multiple references during run-time.
To do this, I was planning on initializing the COMP...
With SDK For Mesh v5.0.0 the mesh_stack_power_down() was actually implemented but there is a bug that will disabled the proxy permanently.
For some unknown reason the mesh_stack_power_down...
