I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I am getting an intermittent "Softdevice assert: 151994:0" error on device initialisation or after the device has run for a period of time. I am using Light Switch Client...
Is there a way to generate a square wave like the one in the picture without using any kind of interruption to change settings middle-wave?
For example, the wave can be...
Hi,
I have been able to use the NRF-9160: Cloud_Client sample for sending data to my AWS IoT MQTT broker on PSM mode from my Thingy91 with a CLOUD_MESSAGE_PUBLICATION_INTERVAL...
Hello, I am trying to implement my own custom bootloader in the nRF52811. I have the softdevice loaded, which then jumps to address 0x19000. This is where I put my bootloader...
Hi,
I'm using nrf52833, flashed by using Jlink SWD programmer. I have no probleme to re-programmed 2/3 of my board.
But the hird gave an error. The strange things...
I am using the gazell protocol of nrf52840 to achieve some functions,but I don't know how to understand the protocol code deeply,anybody has advice or flow chart or relevant...
I want to implement noise sensor based on PDM (pulse density modulation) , But I cant found any PDM driver or API based on Zephyr , I used MP34DT05(st semi-conductor).
So...
I have nrf52832 radios communicating with each other 100%. I have a nrf24l01p that is the 'gateway' to which the nrf52832 sends dump data. I can communicate with nrf24 and...
When i start the nRF mesh app, it crashes immediatly. What do i need to do? I re installed it a couple times and i rebooted my phone a couple times.
The phone is a samsung...
Hi,
I am developing firmware both nrf52 and nrf91.
in nrf52, I activated BLE, usb and uart. Uart communication established between nrf52 and nrf91.
in nrf91, I activated...
Hello, I have done customized board using nRF52832 and when I try to flash code using nRF52 DK(Jtag). I can able to control led's using customized board. But Bluetooth is...
I am using the gazell protocol of nrf52840,how to use broadcast radio mode from host to device based on the gazell protocol ?or can I use the gazell protocol to make it possible...
We have an neural network running on a 52832 using the floating point unit. We started encountering FPU exceptions so we enabled the FPU IRQ to identify which specific instructions...
Hi everyone,
I want to create multiple USB instances using only one nRF52840 dongle. I want to implement one CDC ACM class instance and another one instance that has two...
