Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi. I have some question.
I'm using Mesh with nRF52832.
How get address after provising?
Is there API function?
1. get or set address -> Unicast address.
2...
Hello,
I am trying to configure a Heart rate sensor MAX30101 with nRF51822. I have initialized the sensor correctly as I can see the LEDs turn on. But when I read data from...
Hi, guys. I'm trying to work with Opus applications using PCA10056 v1.0. In order to play Opus fils using the nRF52840,
do I need audio DAC + audio amplifier to create sound...
Hi,
I am using NRF51822 pca10028 UART ble example ,
I need to give provision to change the name of the device after pairing and reset the device so that it starts advertising...
Hello,
I m bonding a central and a peripheral and saving the bonds into a whitelist i use at each startup. When i delete the bonds on central side, the connection to the...
I am using a ultra-miniature (BMD-350) series module from Rigdo which has the nRF52832 BLE SoC. The pins from the nrf52 SoC are all brought out on a female headers on a custom...
I am running a custom board (Ublox Neo dev board) and have a custom board file.
I have modified and and can run code in Segger Embedded Studio based on the peripheral serial...
Hi,
I'm getting a Hardfault MemManage (IPSR 003) when calling sd_ble_gap_adv_stop(). The advertising handle I'm passing is 0. This is called after the advertising has started...
Hi!
I use the peripheral blinky example from the sdk v15.0.0. I ave added some code so that the board is scanning for advertising messages aswell. Every thing works fine...
Hi,
I've just realized the project from
https://github.com/Martinsbl/nrf5-mpu-examples/tree/master/nrf52-mpu-easydma-using-gpiote-and-registers
And it is working quiet...
Hello everyone, I am trying to send and receive messages over UART using Teraterm, the PCA10059 dongle and the UART Android app.
I was following the directions found in...
When I was trying to update the modem firmware, it showed something like this...
Traceback (most recent call last): File "c:\python37\lib\runpy.py", line 193, in _run_module_as_main...
Hi,
I am working on increase data throughput between phone and nrf52832. I am using SDK 15.3.
I create a service and a notify characteristic. I am sending 20-byte packet...
I currently have a hobby product that reads sensors and turns on/off relays based on that sensor input. I've got an nRF52840 that sits on my sensors and relays, and I have...
Hi,
I am working on nRF52832 with MAX30205 temperature sensor , i am comparing the temperature with threshold value like this if (m_sample <threshold) then send the data...
